Bosch Evolution SHU42L02UC Руководство по эксплуатации и уходу - Страница 12

Просмотреть онлайн или скачать pdf Руководство по эксплуатации и уходу для Посудомоечная машина Bosch Evolution SHU42L02UC. Bosch Evolution SHU42L02UC 44 страницы. Bosch dish washer shu42l use and care manual

Bosch Evolution SHU42L02UC Руководство по эксплуатации и уходу
CARE AND MAINTENANCE...continued
6. Clean the Exterior Door Panel
C A U T I O N
POSSIBLE DISHWASHER
DAMAGE:
Your dishwasher's
exterior door panel can be damaged
if you try to clean it with harsh
chemicals, abrasive cleaners,
scouring pads (metal or plastic), or
abrasive cloths/paper towels.
- Colored Doors
a ) Use only a soft cloth that is lightly
dampened with soapy water.
- Stainless Steel Doors
b ) Use a soft cloth with a non-abrasive
cleaner (preferably a liquid spray) made
for cleaning stainless steel. For the best
results, apply the stainless steel cleaner
to the cloth, then wipe the surface.
7. Clean the Door Gasket
a ) Regularly clean the door gasket
with a damp cloth to remove food
particles and other debris.
10

SELF HELP

Dishwashers may occasionally exhibit
problems that are unrelated to a
malfunction of the dishwasher itself. The
following information may help you with a
dishwasher problem without your having
to call a repair person.
Dishes do not dry
The rinse agent dispenser may be
empty. Check the rinse-aid dispenser and
refill it if necessary. Dishware drying can
be accelerated and enhanced by opening
the dishwasher door slightly and propping
it open with the top rack.
Indicator light(s) do not come on
A fuse may have blown or a circuit
breaker tripped. Check the fuse or circuit
breaker at your fuse box/breaker box and
replace the fuse or reset the breaker if
necessary.
Dishwasher does not start
The dishwasher door may not be
properly shut. Make certain the
dishwasher door is shut and latched.
Dishwasher runs a long time
If the dishwasher completes the cycle,
but the run time seems exceptionally
long, it may be due to cold incoming
water. Before starting the dishwasher,
open the hot water faucet at the sink
nearest the dishwasher. Run the water
until it runs hot, then turn off the water
and start the dishwasher.
Machine cycle does not advance to
rinse
NOTE
: The Installation Manual that
came with your Bosch dishwasher will
help you with the following instructions.
The water supply line may be shut off.
Check the water supply valve and open it
if it's shut.
Water not pumped from
dishwasher
Make certain the drain hose isn't
kinked, clogged, or improperly installed.
Make certain a portion of the drain hose
is at least 20 inches above the
dishwasher's enclosure floor (see the
Installation Manual). Filters may be
clogged. Make certain the filter system
isn't clogged (see the Care and
Maintenance section of this manual).
The kitchen sink drain may be clogged;
you may need a plumber rather than a
serviceman for the dishwasher. If an air
gap is installed at sink, it may be
clogged.
SELF HELP
Detergent dispenser cover will not
shut
You may not be correctly shutting the
detergent dispenser cover, or a cycle
was not finished and should be
cancelled. Go to the Adding Detergent
and Rinse Agent section of this manual
for instructions on shutting the dteregent
dispenser cover. Go to the Operating the
Dishwasher section of this manual for
instructions on cancelling a cycle.
White spots left on dishes
More rinse agent is needed. Go to the
Adding Detergent and Rinse Agent
section of this manual for instructions on
increasing the amount of rinse agent
dispensed.
Streaks on glassware
Too much rinse agent is being
dispensed. Go to the Adding Detergent
and Rinse Agent section of this manual
for instructions on decreasing the
amount of rinse agent dispensed.
Rattling noises
Utensils may not be properly arranged.
Suds in dishwasher
You may have used the wrong type of
dishwashing detergent. Use only
automatic dishwasher detergents.
Unsatisfactory washing results
• Incorrect amount of detergent.
• Utensils incorrectly arranged or rack
overloaded.
• Spray arm rotation blocked by
utensils.
• Spray arm nozzles need cleaning.
• Filters not properly fitted into
position.
• Unsuitable cycle selected.