AirStage ARUH36RLAV Руководство по установке - Страница 14

Просмотреть онлайн или скачать pdf Руководство по установке для Кондиционер AirStage ARUH36RLAV. AirStage ARUH36RLAV 15 страниц. Indoor unit (duct type)

Печатать страницу
AirStage ARUH36RLAV Руководство по установке
Rotary
Address
Switch Setting
REF AD SW
Refrigerant
circuit
×10
×1
0
0
0
1
0
1
2
0
2
3
0
3
4
0
4
5
0
5
6
0
6
7
0
7
8
0
8
9
0
9
10
1
0
11
1
1
12
1
2
.
.
.
.
.
.
.
.
.
99
9
9
Do no t set the indoor unit address (IU AD SW) at 64 to 99. It may result in failure.
(3) Remote controller address
Rotary switch (RC AD SW) .... Factory setting "0"
When connecting multiple indoor units to 1 standard wired remote controller, set the
address at RC AD SW in sequence from 0.
Setting
Setting
range
Remote con-
troller
0 to 15
address
Example If 4 indoor units are connected.
Indoor unit
Indoor unit
RC AD SW
RC AD SW
0
Remote
controller
RC AD SW
0
Address
0
RC AD SW
8
Address
8
] 1

7.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up. (Fig. B)
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote controller.
Fig. B
Confusion
Indoor unit
Remote
controller
Custom code setting for indoor unit
Set the DIP SW SET 3 SW1, SW2, referring to the Table B.
En-13
Table A
Rotary
Address
Switch Setting
IU AD SW
Indoor
unit
×10
0
0
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
9
0
10
1
11
1
12
1
.
.
.
.
.
.
63
6
Type of switch
Setting
example
0
RC AD
Indoor unit
Indoor unit
RC AD SW
RC AD SW
1
2
3
1
2
3
4
5
1
2
3
4
5
9
A
B
C
D
9
10
11
12
13
Code change
A
B
C
D
A
B
C
D
SW
SW
SW
SW
1
2
3
4
ON
OFF
Dip switch
"SET 3"
DIP SW
×1
SET 3 SW1
DIP SW
0
SET 3 SW2
1
2
1
3

7.3. Function setting

4
5
• FUNCTION SETTING can be performed with the wired or wireless remote controller.
6
(The remote controller is optional equipment)
7
• Refer to the wired or wireless remote controller manual for detailed setting information.
8
(Set IU AD, REF AD SW to 0)
9
• Refer to "7.1. Setting the address" for indoor unit address and refrigerant circuit address
0
settings.
1
• Turn the power of the indoor unit ON before starting the setting.
2
.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air
.
.
tight test and vacuuming have been conducted before turning on the power.
3
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Function
Function
number
Filter indica-
tor interval
Filter indica-
tor action
Cool air
temperature
trigger
6
7
6
7
Heat air
temperature
trigger
E
F
14
15
Auto restart
External
control
Error report
target
Table B
Custom code
A (Factory setting)
OFF
OFF
Setting number
Default
Adjust the fi lter cleaning interval
00
Default
○
notifi cation. If the notifi cation is too
11
01
Longer
early, change to setting 01. If the
notifi cation is too late, change to
02
Shorter
setting 02.
00
Enable
○
01
Disable
Enable or disable the fi lter indica-
13
tor. Setting 02 is for use with a
Display only
central remote controller.
on central
02
remote
controller
00
Default
○
Adjust the cool air trigger temperature.
To lower the trigger temperature,
30
01
Adjust (1)
use setting 01. To raise the trigger
temperature, use setting 02.
02
Adjust (2)
Adjust the heat air trigger
00
Default
○
temperature. To lower the trigger
temperature by 11 degrees F (6
01
Adjust (1)
degrees C), use setting 01. To
31
02
Adjust (2)
lower the trigger temperature by
7 degrees F (4 degrees C), use
setting 02. To raise the trigger tem-
03
Adjust (3)
perature, use setting 03.
Enable or disable automatic
00
Enable
40
system restart after a power
01
Disable
○
outage.
Allow an external controller to start
00
Start/Stop
○
or stop the system, or to perform
an emergency stop.
* If an emergency stop is performed
Emergency
46
01
stop
* If forced stop is set, indoor unit
02
Forced stop
00
All
○
Change the target for reporting er-
Display only
rors. Errors can either be reported
47
on central
in all locations, or only on the
01
remote
wired remote.
controller
B
C
D
ON
OFF
ON
OFF
ON
ON
Details
from an external controller,
all refrigerant systems will be
disabled.
stops by the input to the external
input terminals, and Start/Stop by
a remote controller is restricted.