Draper Luma Инструкции - Страница 2
Просмотреть онлайн или скачать pdf Инструкции для Проекционный экран Draper Luma. Draper Luma 2 страницы. Spring-roller operated projection screen that can be wall or ceiling mounted
Также для Draper Luma: Брошюра (16 страниц)
Печатать страницу
Luma
Section 1 - Installation
Section 1.1 - Ceiling Suspended Mounting to Joists
1. Use the holes at the front of the endcap/mounting bracket for suspended mounting.
Position and properly anchor screw eyes or other fasteners (not included) into ceiling joists or other solid surface.
Suspend "S" hooks (not included) from fasteners (not included) and hook through holes in the front of the mount-
ing bracket. For added safety, crimp both ends of the "S" hooks so the screen cannot come off.
Recommended hardware (not included):
For mounting into wood or ceiling joist, use two
for mounting into drywall (minimum ½" thick), use
Section 1.2 - Ceiling Suspended Mounting - T-Bar Twist Clips
1. Loosen the clip assembly by turning the formed steel hanger counterclockwise.
2. Spread the clip assembly apart, place over the T-irons, and firmly squeeze the clip assembly back together,
making sure the clip is firmly seated around the T-iron. Retighten by using pliers to turn the formed steel hang-
er clockwise. Make sure it is fully tightened.
3. Secure with the nut. Tighten with pliers.
Please Note:
Make sure the clip is fully tightened around the T-iron, and that the formed steel hanger and the lock nut are fully
tightened. Poorly tightened clip assemblies, hangers or nuts allow the T-Bar Twist Clip to work loose.
4. Test by trying to pull the twist clip open and by pulling down on the hanger. The clip should not pull open.
5 . Suspend provided "S" hooks from the holes in the clips and hook through holes in the front of the screen
mounting bracket. For added safety, crimp both ends of the "S" hooks so the screen cannot come off.
Please Note:
T–Bar Twist Clips are not recommended for screens larger than 70" x 70" unless T-irons are reinforced.
Section 1.3 - Wall Mounting
1. Use the upper portion of the holes at the back of the endcap/mounting bracket for flush wall mounting.
Recommended hardware (not included):
For mounting into wood or wall stud, use #10 x 1¼" wood screws;
for mounting into drywall (minimum ½" thick), use 3/16" toggle or molly bolts.
DO NOT USE FLAT HEAD SCREWS. DO NOT OVERTIGHTEN.
Section 1.4 - Extension Brackets
1. Wall mount the brackets (not included with screen) using hardware recom-mended for "Wall Mounting" (above,
not included). Then, suspend the screen from the front holes with "S" hooks. For added safety, crimp both
ends of the "S" hooks so the screen cannot come off.
DO NOT OVERTIGHTEN.
Please note: When installing wall brackets, flexible driver bit extensions may
make it easier to accurately drive the fasteners into the mounting surface.
Section 2 - Operating Instructions
Section 2.1 -
Standard
pull screen down. Hesitate—then allow screen to retract very slowly until it locks in place.
To lower picture surface:
pull screen down and, while holding, allow for slow retraction into the case to reduce risk of
To raise picture surface:
injury from falling screen.
Section 2.2 -
AutoReturn
To lower picture surface:
pull screen down. Hesitate—then allow screen to retract very slowly until it locks in place.
pull screen down gently until it stops, then release.
To raise picture surface:
(Continued)
/
" x 1¼" screw eyes and
3
16
/
" toggle or molly bolts with
3
16
(Hardware Not Included)
(Optional Equipment)
(Hardware Not Included)
/
" diameter "S" hooks;
3
16
/
" "S" hooks.
3
16
(Optional)
DO NOT mount screens with plastic
endcaps to metal wall brackets in
the manner shown above.
page 2 of 2
Figure (1)
Crimp
Crimp
Clip Assembly
Screen
Nut
Hanger
Crimp
Crimp
Figure (2)
Figure (3)
Figure (4)