Draper Silhouette C Series Инструкции по установке и эксплуатации
Просмотреть онлайн или скачать pdf Инструкции по установке и эксплуатации для Проекционный экран Draper Silhouette C Series. Draper Silhouette C Series 2 страницы. Manually operated projection screens
Также для Draper Silhouette C Series: Руководство по установке/эксплуатации с запасными частями для обслуживания (5 страниц)
Печатать страницу
Manually Operated Projection Screens by Draper
➀
Read instructions through completely before proceeding; keep
them for future reference. Follow instructions carefully. Installation
contrary to instructions invalidates warranty. Care in both mounting
and correct operation willl assure long and satisfactory service from
your Draper screen.
➁
Screen should be accessible for complete removal should fabric
become damaged or for service if required.
➂
Screen should be installed level (using a carpenter's level).
➃
Nothing should be fastened to screen dowel or viewing surface.
➄
Operating crank for Series C is packed separately in screen carton.
Do not discard with packing material.
Note: Screen has been thoroughly inspected and tested at factory
and found to be operating properly prior to shipment.
Installation
Your Draper screen can be mounted on a wall or suspended from the ceiling,
or mounted on special 6" extension bracket. Extension brackets must be
ordered separately from Draper . With each method of installation, the case
must be mounted level and with the flat back parallel to the wall.
To reduce the risk of personal injury, use only the hardware which comes
with the screen or is specified in these instructions.
The screen (or extension brackets) should be mounted into studs or
blocking in the wall/ceiling, or in drywall (minimum thickness
specified anchors. For any other type of installation, follow all local building
and safety codes.
Steel studs, concrete or cinder block walls and all other types of non-wood
frame construction require the use of special screws or anchors. The
selection of appropriate mounting hardware should be made by a qualified
professional installer.
When locating viewing surface and checking clearance for screen's opera-
tion, remember surface is centered in case. Handle case carefully to avoid
scratching. Regardless of mounting method, screen should be positively
and securely supported so that vibration or even abusive pulling on the
viewing surface will not cause case to work loose or fall. Installer must insure
that fasteners used are of adequate strength and suitable for the mounting
surface.
Wall Mounting
Mount 2, 3, or 4 aluminum brackets provided ("Z" Clips) on the wall at desired
height, using appropriate fasteners. Verify that they are in line and level to
fully engage with the mounting lip on back of screen case. 1
is required above the "Z" Clips to allow case lip to be engaged over the lip
of the "Z" Clips.
Engage the lip on back of screen case with lip of "Z" Clip and gently pull down
to fully engage case to brackets.
411 S. Pearl St., Spiceland, IN 47385 USA ❚ 765-987-7999 ❚ fax 765-987-7142
e-mail [email protected] ❚ www.draperinc.com
Copyright © 2000
Installation/Operating Instructions
Silhouette/Series M and C
Caution
5
/
" of free space
8
Form Sil/MCI00
Lip on back
of case
"Z" Clip
(wall mounting bracket
supplied with Silhouette)
Locate 2 offset ceiling brackets (supplied) and slide these into the channel
on top of screen case by angling one side of bracket under lip of channel and
opposite side of bracket above notch in opposite channel lip.
Allow bracket to drop against bottom of channel and then slide it along case
1
/
") with
until it stops against endcap of case. Tighten 2 set screws to lock bracket
2
in place. Make sure that the flange of the ceiling bracket that has 4 holes is
extended beyond the endcaps of the case. Repeat above procedure for
second ceiling bracket, making sure to slide it towards opposite end of case.
To mount against ceiling, hold screen case against ceiling and mark
mounting hole locations. Each bracket has 2 holes towards the front edge
and 2 holes towards the back edge. Installer must use at least 2 fasteners
(front of Silhouette case)
per bracket with one fastener in one of the two holes closest to back edge
of bracket, and one fastener in one of the two holes closest to front edge of
bracket. Installer must insure that fasteners are of adequate strength and
suitable for the mounting surface chosen.
To mount suspended from ceiling, the brackets need to be installed on
screen case as noted above. Attach "S" Hooks (supplied) through the holes
in the brackets. Select the set of holes that allows the screen to hang in a
vertical position. The installer is to provide the materials and fasteners to
attach the "S" Hooks to the ceiling. Installer must insure that the fasteners
and suspension material are of adequate strength and suitable for the
mounting surface chosen.
Printed in U.S.A.
Silhouette fully engaged
on "Z" Clip
Ceiling/Suspended Mounting
Ceiling bracket in
channel of case
Ceiling bracket
Mounting fasteners
(supplied by others, 2 per bracket)
(right end of Silhouette case)