Draper SLX17 Руководство по установке и эксплуатации - Страница 2

Просмотреть онлайн или скачать pdf Руководство по установке и эксплуатации для Проекционный экран Draper SLX17. Draper SLX17 7 страниц. 230v ac scissor lift slx video projector lift
Также для Draper SLX17: Брошюра и технические характеристики (16 страниц), Руководство по установке и эксплуатации (7 страниц), Инструкции по установке и эксплуатации (8 страниц), Руководство по установке и эксплуатации (7 страниц)

Печатать страницу

Draper SLX17 Руководство по установке и эксплуатации

Scissor Lift SLX by Draper

Installing Projector

Generally, the video pro jec tor should be sus pend ed from the Projector

Pan ac cord ing to pro jec tor man u fac tur er's in struc tions and rec om mend ed

stan dard ceiling mounting hardware.

The Scissor Lift SLX has a grounded 110-120V AC, 60 Hz power cord for

pro jec tor power supply. The power cord is laced down the back scissor and is

"hot" at all times.

Control cables should be laced through our Cable Management System.

Make sure to use ﬂ exible cables, and to allow enough cable at each turn

so cables do not stretch or kink. This will ensure that cords do not become

tangled and dam aged during Scissor Lift SLX operation.

Unit and projection system should be operated, checked and ad just ed as

necessary at this time.

NOTE: Immediately upon completion of the surrounding ceiling, units should

be operated to conﬁ rm that optional ceiling closure panel stops just short of

touching ceiling in closed position.

Warning: Keep ﬁ ngers and other objects away from automatic ceiling

closure and scissor mechanisms when unit is operating. Serious injury or

damage could result.

Lifting Cable Bar

Installing Optional Universal Projector Mount

If you ordered the unit with optional Universal Projector Mount pre-installed,

disregard these instructions.

If you did not order the mount pre-installed, you will need to install a new

Projector Pan, which includes the Universal Projector Mount's rectangular

plate.

① Lower unit until the Bottom Pan is resting on a tabletop or other stable and

sturdy surface.

② Remove Lifting Cable Bar from Bottom Pan (see Fig. 2).

③ Remove bolts holding Projector Pan to Bottom Pan (see Fig. 2).

④ Remove Projector Pan and set aside.

⑤ Place new Projector Pan with Universal Mount into place.

⑥ Re-attach Projector Pan to Bottom Pan.

⑦ Re-attach Lifting Cable Bar to Bottom Pan.

The Projector Pan can be moved forward or back.

① Make sure Bottom Pan is supported.

② Remove the Lifting Cable Bar (see Fig. 2).

③ Remove screws holding Projector Pan on Bottom Pan (see Fig. 2).

④ Move Bottom Pan forward or back.

⑤ Replace screws.

⑥ Replace Lifting Cable Bar.

Run the unit to its "Service" position and make sure pan is level. Try and set

so that pan is not more than ¾" out of level. However, the pan does not

have to be perfectly level, as long as the positioning is consistent and

repeatable in "Show" and "Closed" positions.

① Make sure Bottom Pan is supported.

② Remove screws holding Lifting Cable Bar to the Bottom Pan (see Fig. 2).

③ Move Lifting Cable Bar forward or back (see Fig. 2).

④ Replace screws.

⑤ Check level again. If still not level, repeat.

Attachment points

for Lifting Cables

¼"-20 x ¾" hex head

cap screws for attaching

Projector Pan to Bottom Pan

Figure 2

www.draperinc.com

(765) 987-7999

Adjusting for Level or Center of Gravity

Preferred Method—Adjusting Projector Pan

Secondary Method—Adjusting Lifting Cable Bar

(if above does not work)

12"

Figure 3

page 2 of 7

"-18 x 1" hex head cap

screws for attaching Lifting

Cable Bar to Bottom Pan