Bosch WAE24166GB Руководство по установке

Просмотреть онлайн или скачать pdf Руководство по установке для Стиральная машина Bosch WAE24166GB. Bosch WAE24166GB 6 страниц.
Также для Bosch WAE24166GB: Руководство по эксплуатации (8 страниц)

Печатать страницу

Safety instructions

- The washing machine is heavy caution when lifting it.

- Warning: Frozen hoses may tear/burst. Do not install washing machine in areas where there

is a risk of frost and/or outdoors.

- Washing machine may be damaged. Do not lift by projecting components (e.g. washing

machine door).

- In addition to the instructions mentioned here, special regulations of the relevant water

and power supply companies may apply.

- If in doubt, have the appliance connected by a technician.

- Lay hoses and cables in such a way that there is no risk of stumbling.

Humidity in the drum

Scope of delivery

is caused by the final

according to model

Model:

Aqua Stop

Aqua Secure

Standard

Power cord

Water drainage

Water supply

Wrench (according to model)

Covers

Elbow

for fixing the waste water

hose

Depending on the connection

- 1 hose clip

24-40 mm (specialist outlet) for connection of the siphon is also required ->

page 4; Water connection.

Useful tool

- Spirit level for alignment.

Installation area

- Stability is important to prevent the machine from wandering!

- The installation area must be firm and level.

- Soft floors/floor coverings are not suitable.

If installing the appliance on a base

- The feet of the appliance must be secured with holding brackets;

order no. WMZ 2200, WX 9756, CZ110600, Z 7080X 0.

If installing the appliance on a wooden joist

- If possible, install the washing machine in a corner.

- Screw a water resistant wooden panel (min. 30 mm thick) to the floor.

- The feet of the appliance must be secured with holding brackets; order no. see above.

Hose and cable lengths

depending on model

Connection on left side

100 cm

145 cm

95 cm

inspection.

85 cm

Standard and Aqua Secure models: min. 60 cm max. 100 cm

Aqua Stop model: 0 max. 100 cm

Available from dealer/customer service:

- Extension for Aqua Stop and cold water inlet hose (approx. 2.50 m),

Order no. WMZ 2380, WZ 10130, CZ11350, Z 7070X 0.

- Longer supply hose (approx. 2.20 m), for standard model.

Built under/Built in appliance

Build under/build in before connection to the power supply.

Installed in between kitchen units

(built under or built in)

- 60 cm cavity width required.

- Install washing machine only under a continuous worktop connected

firmly to the adjacent cupboards.

Built under appliance

Risk of electric shock!

- 60 cm cavity width required.

- Instead of the appliance cover panel, have a technician install a sheet

metal cover * (* order no. WMZ 2420, WZ 10190).

Remove transportation protection

devices

Connection on right side

- Before using the appliance for the first time, remove all the transportation

protection devices and retain for subsequent transportation of the

appliance.

- For any future transport, the transport braces must be refitted this

prevents the machine from being damaged. -> page 6.

- Keep the bolt and sleeve screwed together.

1. Take the hoses and elbow out of the holders, depending on model.

135 cm

2. Loosen the bolts ....

... until they are freely movable in the sleeves.

3. Completely remove all 4 transportation protection devices and

take the mains cable out of the holder.

4. Insert covers.

Water connection

depending on model

- Risk of electric shock! Do not immerse Aqua Stop safety device in water

(contains an electric valve).

- To prevent leakage or water damage, follow the instructions in this chapter!

- Attention: Operate the washing machine with cold drinking water only.

Do not connect to a mixer tap of a pressureless hot water heater.

- Do not use a used inlet hose. Only use the inlet hose supplied or one which was purchased

from an authorised specialist dealer.

- If in doubt, have the appliance connected by a technician.

Water supply

Water supply hose:

Attention: Do not kink, crush, modify or sever water supply hose

(strength is no longer guaranteed).

Optimum water pressure in the mains: 100-1000 kPa (1-10 bar)

- When the tap is turned on, the water flow is at least 8 l/min.

- If the water pressure is higher, install a pressure reducing valve.

Model:

Aqua Stop

Aqua Secure

1. Connect water supply hose to the tap.

Tighten plastic screw fittings by hand only.

2. Open water tap carefully, checking the leak tightness

max.

of the connection points.

90_

Attention: Screw fitting is under mains water

pressure.

min. 10 mm

Water drainage

Water drainage hose:

Attention: Do not kink or protract the drainage hose.

Height difference between installation area and outlet:

- min. 60 cm - max. 100 cm for aqua secure and standard models

- 0 - max. 100 cm for aqua stop model

Drainage into a washbasin:

Attention: Secure the drainage hose from slipping out.

Attention: The washbasin outlet must not be sealed by the plug.

Check that the water is pumped out quickly enough. Do not insert the end

of the drainage hose into the pumped off water! There is a risk that water

will be drawn back into the washing machine!

Drainage into a siphon:

Attention: Secure connection point with hose clip,

24-40 mm (dealer).

Standard

3/4"

min. 10 mm

max.

90_

3/4"