Draper Futureguard FlexShade Zip Руководство по установке - Страница 6

Просмотреть онлайн или скачать pdf Руководство по установке для Внутренняя отделка Draper Futureguard FlexShade Zip. Draper Futureguard FlexShade Zip 7 страниц.

Печатать страницу

Futureguard® FlexShade Zip™

ALTERNATE MOUNTING

(Zip 127 Angled Only)

If the system is installed in a recess, it is unlikely that there will be

sufficient space above the Side Channels to allow the Headbox to be

mounted onto them after the channels are installed. In these instances,

we recommend using the wall/permanent mounting procedure.

The minimum depth of the ceiling pocket for the Flex Shade Zip 92 is 4¾"

(120mm), and for the FlexShade Zip 127 is 6¼" (158mm). See Fig. 17.

The FlexShade Zip operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and

supplied with a 6' cable lead (standard). Longer lead can be substituted by removing two screws in motor end

of roller, removing lead, plugging new lead in, and replacing screws. Wire to connect shade to switch(es) and

switch(es) to power supply should be furnished by installer. Connections should be made in accordance with

attached wiring diagram, and wiring should comply with national and local electrical codes.

DO NOT wire 4-wire motors in parallel without written permission from Futureguard.

All operating switches should be "off" before power is connected.

PROGRAMMING AND LIMIT SWITCH ADJUSTMENTS

INITIATE PROGRAMMING

Connect AC to one motor at a time. Select the transmitter/channel

you want to use. Press and hold both the Up and Down buttons

simultaneously until the motor jogs, then release (a jog is a short up

and down movement of the motor).

CHECK/CHANGE THE DIRECTION

Check the direction of operation (the motor will operate in momentary

fashion). Confirm that the Up button brings the application up or in. To

change the direction, press the Stop button for more than 5 seconds

until the motor jogs, then release. Check the direction.

SETTING THE LIMITS

Start at and upper reference point (upper limit). Press both the Stop

and Down buttons simultaneously until the motor begins to rotate,

then release. Stop the motor where you want to set the lower limit.

Adjust if necessary by pressing the Up or Down buttons.

Press and hold both the Stop and Up buttons simultaneously until

the motor rotates up, then release. Stop the motor where you want

to set the upper limit (or it will stop automatically at the initial upper

reference point). Adjust if necessary. Press the Stop for 5 seconds until

the motor jogs. The limits are now recorded.

Press the Programming button for 3 seconds until the motor jogs to

record the transmitter for user mode (the motor operates in maintained

fashion).

by Draper

FOR JAMB RECESSED AND POCKET INSTALLATIONS

FlexShade Zip 127

6¼" (

158mm)

5" (

127mm)

(

127mm)

Complete Electrical Connection

FlexShade Zip 92

4 ¾"

(120mm)

(92mm)

7¼"

(

183mm)

Figure 17

Figure

RTS ALTUS MOTORS

ADD/DELETE A TRANSMITTER/CHANNEL

To add a transmitter/channel, press the programming button on an

already recorded one until the motor jogs. Select the transmitter/channel

to add and press its programming button until it jogs, then release.

To delete a transmitter/channel, press the programming button on an

already recorded one until the motor jogs. Select the transmitter/chan

nel to delete and press its programming button until it jogs, then release.

SETTING THE INTERMEDIATE LIMIT

Once the limits are set the motor is in user mode. Operate the motor to

the location you would like as your intermediate position with and already

programmed transmitter/channel and press the Stop . Release and press

the Stop button again for 5 seconds until the motor jogs, then release.

Check it (to access the intermediate position press the Stop button

while the motor is at rest).

RESETTING THE LIMITS

To change the lower limit: Move the motor to its current lower limit

position and let it stop. Press the Up and Down buttons simultaneously

until the motor jogs, then release. Adjust to a new lower limit position.

Press the Stop until the motor jogs, then release. Check it.

To change the upper limit: Move the motor to its current upper limit

position and let it stop. Press the Up and Down buttons simultaneously

until the motor jogs, then release. Adjust to a new upper limit position.

Press the Stop until the motor jogs, then release. Check it.

FlexShade Zip 127

6¼" (

158mm)

5" (

127mm)

(92mm)

(148mm)

Radio Technology 110-120V Motors

Radio Technology 110-120V Quiet Motor

Internal Shade Wiring

White (Neutral)

Black

Green (Ground)

Dashed wiring

by electrician

To 110-120V Line

page 6

(

127mm)

7¼"

(

183mm)

RF Wall Switch or

RF Transmitter