Draper LightBloc ZIP 92 Инструкции по установке и эксплуатации - Страница 8

Просмотреть онлайн или скачать pdf Инструкции по установке и эксплуатации для Внутренняя отделка Draper LightBloc ZIP 92. Draper LightBloc ZIP 92 12 страниц.

Печатать страницу

LightBloc ZIP™ 92 & ZIP 127

Section 9 - Limit Setting: Standard and Quiet Motors

Caution: Unit ships without limits. Limits will need to be set

before the unit is operated. Always be prepared to shut off

manually when new adjustment is being tested.

Push Button Limits

1. Fully depress both limit switch push buttons, then

operate wall switch to make sure system works properly.

2. Raise shade to desired "UP" stop position.

3. Set upper limit by depressing proper

push button.

(back)

4. Lower shade to desired "DOWN" stop position.

5. Set lower limit by depressing proper

Screw-Type Limits

6. Determine which direction of fabric travel corresponds

with arrows on motor.

7. Operate shade to desired "down" stop position.

Set limit by turning proper socket toward "+" to lower limit, and "-" to raise it.

8. Operate shade to desired "up" stopping position.

Set limit by turning proper screw toward "-" to raise limit, and "+" to lower it.

Please Note: Each full rotation of the limit screw equals approximately

5/ 8 "

of shade travel, which may require rotating the limit screw

(16mm)

several times.

Caution: DO NOT allow the hem bar to hit the upper roller or fascia.

This will damage the unit.

Caution: DO NOT allow hem bar to retract into the headbox.

Section 10 - Complete Electrical Connection

Operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch

. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to connect

(standard)

shade to switch

and switch

(es)

wiring should comply with national and local electrical codes.

DO NOT wire motors in parallel without written permission from Draper

All operating switches should be "off" before power is connected.

Controls & System Overview

Sonesse

RTS 120VAC Motors

RTS

MOTOR

120V

110-120V Line

Dashed Wiring

by Electrician

Sonesse

is a registered trademark of Somfy

push button.

(front)

to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and

Patio

RF Remote

STOP

Decora RTS

Wireless Keypad

Systems, Inc.

Caution:

- Be sure all switches are in "off"

position before adjusting limit

switches.

- Shade may be damaged by

running shade fabric up too far

and exposing roller.

- If using a group control system,

each limit switch must be set

prior to connecting to system.

- Motor must be installed so

limit switches are pointed up or

accessible.

fully boxed, and supplied with a 6'

(es)

Controls & System Overview

Sonesse

110-120V Line

ROOM SIDE

Front

Back

GLASS SIDE

PUSH BUTTON LIMITS

ROOM SIDE

Front

Back

GLASS SIDE

Bottom View

GLASS SIDE

SCREW-TYPE LIMITS

ROOM SIDE

Front

Side View

Front

Back

Screws

Back

GLASS SIDE

Bottom View

GLASS SIDE

Bottom View

Screws

Side View

Screws

Side View

(183 cm)

120VAC Motors

NOTE: Test shade operation

120V

If shade direction does not

MOTOR

correspond with the switch

orientation, turn power back

red

and black

off and switch the

wires from the motor to the switch.

Do not wire motors in parallel without

written permission from Draper.

Control

Switch

Single Gang

Box (by others)

Dashed Wiring

by Electrician

page 8 of 12

Standard right-hand

Bottom View

motor configuration shown

Side View

Standard right-hand

Bottom View

motor configuration shown

Side View

cable lead