Bosch 300 Series Краткое руководство по эксплуатации и технике безопасности - Страница 6

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации и технике безопасности для Печь Bosch 300 Series. Bosch 300 Series 13 страниц. Built-in wall ovens
Также для Bosch 300 Series: Руководство по эксплуатации (40 страниц), Руководство пользователя (21 страниц), Руководство по установке (6 страниц), Руководство по установке (36 страниц), Руководство по установке (32 страниц), Руководство по эксплуатации и уходу / инструкция по установке (40 страниц), Руководство по эксплуатации (50 страниц), Краткое руководство по эксплуатации и технике безопасности (7 страниц), Руководство по установке (28 страниц), Краткое руководство по эксплуатации (7 страниц), Руководство по эксплуатации и уходу (32 страниц), Краткое руководство по эксплуатации и технике безопасности (7 страниц), Руководство по эксплуатации (36 страниц)

Печатать страницу
Bosch 300 Series Краткое руководство по эксплуатации и технике безопасности
5 Settings

5.1 Available Settings

Below are some commonly used settings. To see all the settings refer to the full online manual or go to Dishwasher » Settings in
the Home Connect
app.
®

5.2 Adjusting the settings

First Steps to adjust any setting:
Open the door and press the ON/OFF button.
Hold down Button A for 3 seconds, until the Rinse Aid
indicator light flashes.
Release button, then follow steps below to adjust specific
setting.
To adjust the rinse aid:
1.
Press the Start button repeatedly until the right amount
of rinse aid has been set. 0 (off), 1(low), 2(medium),
or 3(high) LEDs above cycle buttons will light up
accordingly.
2.
Press button A for 3 seconds to save the setting.
To turn on intensive drying:
1.
Press button A until the Clean and Sanitize lights flash.
2.
Press the Start button until 1 LED light above the heavy
cycle button is on (intensive dry is on).
3.
Press button A for 3 seconds to save the setting.

6 Frequently Asked Questions

Q:
Why is food remaining on dishes after I run the cycle?
•
It is possible the dishes do not have adequate clearance between them. Also, be sure nothing is blocking the spray arms and
that the filter is clean. Select the Heavy cleaning cycle.
Q: Why does the cycle run a long time?
•
Sensors in the dishwasher automatically increase the cycle time to ensure a good wash when heavy soil is detected.
•
Incoming water may not be hot enough and dishwasher has to heat it.
Setting
Rinse Aid
Off/Low/Medium/High
Intensive drying
Off/On
End of cycle tone
Off/Low/Medium/High
Factory setting
Description
Medium
Setting to adjust the amount of rinse aid
used in each cycle.
Off
Setting to increase drying ability for glass-
es or plastic. Increases cycle length and
temperature.
Medium
The volume of the tone signalling the end
of cycle.
To adjust the signal volume:
1.
Press button A until the Clean and Rinse Aid lights flash.
2.
Press the Start button repeatedly until the preferred
volume level has been selected. 0 (off), 1(low), 2(medi-
um), or 3(high) LEDs above cycle buttons will light up
accordingly.
3.
Press button A for 3 seconds to save the setting.
To reset to factory settings:
1.
Press button A until the Clean, Sanitize and Rinse Aid
lights flash.
2.
Press the Start button. The 3 LEDs above cycle buttons
will blink alternatively for 1 minute. The factory settings
have been restored.
Tip: The simplest way to change the settings is with the
Home Connect
app.
®