Alemlube G100120 Техническое руководство пользователя - Страница 6
Просмотреть онлайн или скачать pdf Техническое руководство пользователя для Инструменты Alemlube G100120. Alemlube G100120 11 страниц. 20kg grease kit
Печатать страницу
Important Notes
1. If you suspect that the spray tip/nozzle or hose is completely clogged, or that pressure has not been fully relieved
after following the steps above, VERY SLOWLY loosen the retaining nut or hose end coupling and relieve pressure
gradually, then loosen completely. Now clear the tip/nozzle or hose.
2. On the pump downstroke, the shovel washer extends beyond the intake cylinder to pull the material into the pump.
The shovel washer works under extreme force. During operation and whenever the pump is charged with air,
the shovel washer can severely injure or amputate a hand or finger or break a tool, if caught between it and the
intake cylinder. Always follow the Pressure Relief Procedure below, before checking, clearing, cleaning, flushing
or servicing any part of the pump.
3. This equipment conducts very high fluid pressure. Spray from the grease control valve, leaks or ruptured
components can inject fluid through your skin and into your body and cause serious body injury.
NEVER point the grease control valve at anyone or at any part of the body.
NEVER put hand or fingers over the spray tip.
ALWAYS follow the Pressure Relief Procedure, right, before cleaning or removing the spray tip or servicing
any system equipment.
NEVER try to stop or deflect leaks with your hand or body.
Be sure equipment safety devices are operating properly before each use.
4. Any misopertation of the system equipment or accessories, such as overpressure, modifying parts, using
incompatible chemicals and fluids or using worn or damaged parts, can cause them to rupture and result in fluid
injection, splashing in the eyes or on the skin, or other serious injury, or fire, explosion or property damage.
NEVER alter or modify any part of this equipment; doing so could cause if any malfunction.
CHECK all equipment regularly and immediately repair or replace worn or damaged parts.
System Pressure
NEVER exceed the recommended working pressure or the maximum air inlet pressure stated on your pump.
Be sure that all dispensing equipment and accessories are rated to withstand the maximum working pressure
of the pump. DO NOT exceed the maximum working pressure of any component or accessory used in the system.
Fluid Compatibility
The system is only suitable for grease.
5. High pressure fluid in the hoses can be very dangerous. If the hose develops a leak, split or rupture due to any
kind of wear, damage or misopertation, the high pressure spray emitted from it can cause a fluid injection injury
or other serious injury or property damage.
TIGHTEN all fluid connections securely before each use. High pressure fluid can dislodge a loose coupling or allow
high pressure spray to be emitted from the coupling.
NEVER use a damaged hose. Before each use, check the entire hose for cuts, leaks, abrasion, bulging cover,
damage or movement of the hose couplings. If any of these conditions exist, replace the hose immediately.
DO NOT try to mend it with tape or any other device. A repaired hose cannot safely contain the high pressure fluid.
NSW/ACT
QLD/PNG
TEL: (02) 9939 0711
TEL: (07) 3889 8480
FAX: (02) 9939 0411
FAX: (07) 3889 8490
OWNER'S TECHNICAL MANUAL
20KG Grease Kit
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
Visit our website at
www.alemlube.com.au
WA
SA/NT
TEL: (08) 9209 3066
TEL: (08) 8241 7111
FAX: (08) 9209 3933
FAX: (08) 8241 7011
or
www.alemlube.co.nz
G100120
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
6