Alemlube G10030 Инструкции по обслуживанию
Просмотреть онлайн или скачать pdf Инструкции по обслуживанию для Инструменты Alemlube G10030. Alemlube G10030 3 страницы. Air operated grease gun
Печатать страницу
Description
Model G10030 is our EL (Entry Level) air operated grease gun designed and engineered for 450gm grease cartridges or bulk grease.
The G10030 provides the user with the flexibility of a continuous flow of grease or one shot trigger action. The gun comes complete
with a separate air vent & filler nipple, a separate bleeder valve and a 30cm long high pressure flexible extension and hydraulic
coupler.
Specifications
Uses
Air Operated Grease Gun - 450gm grease cartridge fill or bulk grease fill. Suitable for most greases up to NLGI2
Discharge Qty
Single shot: Approx. 1cc per shot. Continuous Flow: Approx 3.5cc per shot or 210cc per minute (without counter
pressure) using NLGI2
Grease Pressure
40:1 ratio. Maximum operating pressure 6,000psi
Air Pressure
Min: 60psi / Max: 150psi. Recommended operating pressure 90psi
Weight
1.8kg
Operating Instructions for 3 Way Loading Cartridge Loading
a) Remove the gun head from the barrel.
b) Draw back the plunger handle all the way.
c) Insert the open end of the cartridge into the barrel & push all
the way in. Remove the seal or pull tab end from the cartridge.
d) Reassemble the gun head to the barrel. Press the catch
plate & release the plunger rod. Pull down the plunger handle.
Loading Via a Bulk Loader Pump
a) Draw back the plunger handle all the way.
b) Insert loader nipple into the loader pump valve.
Make sure the nipple is the type that fits the loader valve.
c) Operate the grease gun from the loader pump.
d) Disconnect the grease gun from the loader pump.
Press the catch plate & release the plunger rod.
Pull down the plunger handle.
Bulk Filling
a) Remove the gun head from the barrel.
b) Draw back plunger entirely. Fill bulk grease into empty container tube. Reassemble the gun
head to the barrel. Press the catch plate & release the plunger rod. Pull down the plunger handle.
Important
*Add oil daily through air fitting before use.
If your gun stops pumping, it may be due to air pockets in the gun. To remove the air, unscrew the gun head 1 to 2 turns and do the
following: Draw back plunger rod fully & release quickly. Repeat several times. This will help exert force to move the follower cup into
the cartridge & expel the air pockets which is essential for a grease gun to work. Push plunger rod all the way in. Tighten the head to
the barrel. If cartridge loading is being used, it could cause the follower cup to warp & contract over time when inside a grease
cartridge & soaking in grease over time.
1. If you change the loading way to pump loading or bulk loading, there is a normal phenomenon that a little amount of grease may
seep out from the bottom of the barrel.
2. In order to avoid this happening, please review the length of time & best method of loading for you (depending on the variety of
grease that your local supplier offers) & use that loading method with minimal change for the best results & longevity of the gun.
(Do not use MULTI LOADING alternately)
3. The gun is now ready to be used.
Limited Warranty
1. The manufacturer warranty's this product against defects in material & craftsmanship for 12 months from date of purchase.
2. The manufacturer's liability is limited to the replacement or repair of the defective material within the warranty period, when
returned freight prepaid to Alemlube or our designated service agent.
3. The warranty does not cover damage caused by accident, misuse or faulty installation.
NSW
TEL: (02) 9939 0711
FAX: (02) 9939 0411
Visit our website at
EL SERIES
VIC/T S
TEL: (03) 8787 8288
FAX: (03) 8787 8266
www.alemlube.com.au
SERVICE INSTRUCTIONS
G10030
ir Operated Grease Gun
QLD
S /NT
TEL: (07) 3889 8480
TEL: (08) 8241 7111
FAX: (07) 3889 8490
FAX: (08) 8241 7011
Email - [email protected]
W
TEL: (08) 9209 3066
FAX: (08) 9209 3933