Bosch 2-26 DE Оригинальное руководство по эксплуатации - Страница 8
Просмотреть онлайн или скачать pdf Оригинальное руководство по эксплуатации для Электроинструмент Bosch 2-26 DE. Bosch 2-26 DE 13 страниц. Gbh professional
Также для Bosch 2-26 DE: Оригинальное руководство по эксплуатации (27 страниц), Оригинальное руководство по эксплуатации (15 страниц)
Печатать страницу
16 | English
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 02.12.2013
Assembly
Before any work on the machine itself, pull the mains
plug.
Auxiliary Handle
Operate your machine only with the auxiliary handle 14.
Changing the position of the auxiliary handle
(see figure A)
The auxiliary handle 14 can be set to any position for a secure
and low-fatigue working posture.
– Turn the bottom part of the auxiliary handle 14 in counter-
clockwise direction and swivel the auxiliary handle 14 to
the desired position. Then retighten the bottom part of the
auxiliary handle 14 by turning in clockwise direction.
Pay attention that the clamping band of the auxiliary handle
is positioned in the groove on the housing as intended for.
Adjusting the Drilling Depth (see figure B)
The required drilling depth X can be set with the depth stop 13.
– Press the button for the depth stop adjustment 12 and in-
sert the depth stop into the auxiliary handle 14.
The knurled surface of the depth stop 13 must face down-
ward.
– Insert the SDS-plus drilling tool to the stop into the SDS-
plus tool holder 3. Otherwise, the movability of the SDS-
plus drilling tool can lead to incorrect adjustment of the
drilling depth.
– Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop correspond with
the desired drilling depth X.
1 609 92A 03Z | (2.12.13)
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Selecting Drill Chucks and Tools
For hammer drilling and chiselling, SDS-plus tools are re-
quired that are inserted in the SDS-plus drill chuck.
For drilling without impact in wood, metal, ceramic and plas-
tic as well as for screwdriving, tools without SDS-plus are
used (e.g., drills with cylindrical shank). For these tools, a
keyless chuck or a key type drill chuck are required.
GBH 2-26 DFR: The SDS-plus quick change chuck 2 can easi-
ly be replaced against the quick change keyless chuck 1 pro-
vided.
Changing the Key Type Drill Chuck
(GBH 2-26 E/RE/DE/DRE)
To work with tools without SDS-plus (e.g., drills with cylindri-
cal shank), a suitable drill chuck must be mounted (key type
drill chuck or keyless chuck, accessories).
Mounting the Key Type Drill Chuck (see figure C)
– Screw the SDS-plus adapter shank 20 into a key type drill
chuck 19. Secure the key type drill chuck 19 with the se-
curing screw 18. Please observe that the securing
screw has a left-hand thread.
Inserting the Key Type Drill Chuck (see figure C)
– Clean the shank end of the adapter shank and apply a light
coat of grease.
– Insert the key type drill chuck with the adapter shank into
the tool holder with a turning motion until it automatically
locks.
– Check the locking effect by pulling the key type drill chuck.
Removing the Key Type Drill Chuck
– Push the locking sleeve 5 toward the rear and pull out the
key type drill chuck 19.
Removing/Inserting the Quick Change Chuck
(GBH 2-26 DFR)
Removing the Quick Change Chuck (see figure D)
– Pull the lock ring for the quick change chuck 6 toward the
rear, hold it in this position and pull off the SDS-plus quick
change chuck 2 or the quick change keyless chuck 1 to-
ward the front.
– After removing, protect the replacement chuck against
contamination.
Inserting the Quick Change Chuck (see figure E)
– Before inserting, clean the quick change chuck and apply a
light coat of grease to the shank end.
– Grasp the SDS-plus quick change chuck 2 or the quick
change keyless chuck 1 completely with your hand. Slide
the quick change chuck with a turning motion onto the drill
chuck mounting 21 until a distinct latching noise is heard.
– The quick change chuck is automatically locked. Check the
locking effect by pulling the quick change chuck.
Bosch Power Tools