Anchor portavox Руководство пользователя - Страница 5
Просмотреть онлайн или скачать pdf Руководство пользователя для Стереосистема Anchor portavox. Anchor portavox 6 страниц. Portable
Печатать страницуWireless Operation
About the transmitter battery gauge/indicator
Assuming a battery is installed in the transmitter, you can
OFF
PWR
estimate the remaining operating time by sliding the power
switch to the PWR position (first turn the sound system off, or
set the transmitter mute switch to the MUTE position).
BAT
ON
Observe the color of the LED indicator(s) that light up:
Battery LED Indicator
MUTE
green
green & amber
amber
Operating times
red
determined
using a fresh
Replacing the transmitter battery
9 volt alkaline
Note: The transmitter power switch must be in the OFF position!
battery *Duracell
MN1604 or
HANDHELD: Unscrew the battery compartment cover on
equivalent.
the lower end of mic (see diagram on previous page). Install
a fresh 9 Volt alkaline battery* and replace the cover.
BODY-PACK: Press the end of the battery cover labeled
slide it back and lift the cover. Install a fresh 9 Volt alkaline
battery* being sure to observe proper polarity. Close the cover.
Operating the wireless microphone system
The audio signal from the built-in wireless receiver is fed to
the Mic 2/Wireless input. Unplug any other mic from the
MIC 2 input when using the wireless system.
Operating the wireless microphone system:
1. Extend the antenna on the PortaVox unit.
2. If you're using the body-pack transmitter, insert the
MIC 2
plug from the mic into the jack on the transmitter.
(
)
WIRELESS
3. Set the Mic 2/Wireless volume control to minimum.
4. Turn the sound system power switch ON.
5. Set the transmitter power switch to PWR and the
mute switch to ON. Note: The domestic version of the
PB-500W has a TX-ON indicator to indicate wireless
signal (RF) is being received.
6. Adjust the Mic 2/Wireless control to desired volume.
Caution: Harmful feedback may occur when walking in front of a
sound system or speaker with a wireless microphone. Always point
mic away from speakers.
8
(PB-500W only)
Operating Time
6 - 20 hours
4 - 6 hours
2 - 4 hours
< 1 hour
,
OPEN
Operation
Mic 1 Input
(1/4" phone jack)
MIC 1
Mic 2 Input
(1/4" phone jack)
MIC 2
(WIRELESS)
Line Input
(1/4" phone jack)
LINE
Power / Battery
Indicator
BATTERY
Flashing = low battery.
Speaker Outputs
(1/4" phone jack)
SPEAKER
OUTPUTS
Charging Indicator
BATTERY CHARGER
Wireless
Flashing = fully charged.
Reception
Indicator
TX ON
(PB-500W
CA
domestic only)
Operating the sound system
1. Unhook the two speakers from the center console and
set them in front of your audience. For best results, use
stands to elevate the speakers 4-6 feet above ground level.
2. Plug the cable attached to each speaker into the jacks
on the console labeled SPEAKER OUTPUT.
3. Plug a microphone into the MIC 1 or MIC 2 input,
or plug an audio source into the LINE input.
4. Set all input controls to minimum, then turn the
power switch "ON." (LED next to switch will light).
If the LED flashes or does not light, the battery must be
charged (see page 9).
5. Increase the level control adjacent to the input used to
desired volume.
6. Adjust the tone control for desired sound quality.
Mic 1
Volume Control
Mic 2 / Wireless
Volume Control
Mic 2 / Wireless
Volume Control
Line Input
Volume Control
Power Switch /
Tone Control
POWER / TONE
Charger Input
(use RC-16 only;
RC-16/220 for export)
5