Formax FD 8650HS Руководство по эксплуатации - Страница 2
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Измельчитель бумаги Formax FD 8650HS. Formax FD 8650HS 2 страницы. High-security w/autooiler cross-cut paper shredder
Печатать страницу
Specifications
Cutting Style:
Cross Cut
Shred Size:
1/32" x 3/16" (Level 6)
Sheet Capacity:
14 - 15 sheets*
Speed:
Up to 24 feet per minute
Feed Opening:
16"
Dimensions:
28" W (includes oil reservoir) x 24" D x 43" H
Security Level
Level 6 (HIPAA Compliant)
Bin Capacity:
53 gal.
Weight:
319 lbs
Power supply:
110V, 50/60Hz 20A
Does not accept credit cards, staples or paper clips
* Capacity varies depending on paper and power supply
Set-up Guidelines
1. Install the shredder on a level surface, away from heat sources and direct sunlight.
2. Insert plug into wall outlet with the appropriate voltage, 110V. If the outlet is shared
with another electronic device, the total current should not exceed 30A (at 110V).
Operation
1. Flip the power switch "ON" located on the right side of the shredder.
2. Auto Start/Auto Stop
When the START button is pushed, the "AUTO" LED will light. Insert
paper to shred. The shredder will start and stop automatically when
using this function.
3. Manual Operation
If paper is too small for the shredder's sensors to detect, shred it
manually. Push the START button once more and the "MANUAL" LED
will light. Insert paper to be shredded. Three minutes after shredding,
the cutter automatically stops rotating.
4. Reverse Operation
Push the REV button and the "REV" LED will light and cutters will
operate in reverse. If too much paper is inserted at one time in
standard modes, the shredder will automatically operate in reverse. If
this occurs, remove the inserted paper and shred in smaller amounts.
NOTE: The maximum amount of paper to be shredded differs
according to paper quality, humidity and voltage. If the shredder is to
be used continuously, do not insert more than half of the maximum capacity.
5. Full Sensor
If the wastebasket is full, the "FULL" LED will light and the cutter will stop
automatically. Open the door, remove and empty the waste bin. Replace the waste
bin, close door, and press START to resume shredding.
AutoOiler
The AutoOiler pumps 20 ml of oil onto the cutting head every 30 minutes to help keep the
FD 8730HS working at peak performance.
1. Fill oil reservoir with recommended HS shredder oil.
2. Insert hose into the top of the bottle.
3. The oiler is ready for use.
ECO Mode
When the power switch on the right side of the shredder (see below) is initially turned on,
the shredder is automatically in ECO Mode. This energy-saving feature puts the shredder
into standby after 5 minutes of inactivity.
When the shredder is in standby, the ECO Mode LED on the control
panel will be lit.
To exit ECO Mode: Turn the power switch to the off position, then while pressing the stop
button turn the shredder back on, hold the stop button down until the shredder beeps
once and release. The Eco Mode indicator LED will go out indicating that the shredder
is no longer in Eco Mode. To re-engage Eco Mode simply turn the shredder off and back
on again.
Safety Precautions
To avoid personal injury, and damage to the shredder,
observe the following safety precautions. Please keep these
instructions for future reference.
NOTE: In case of emergency, flip the "Power Switch"
to cut off power and/or pull the plug out of the wall outlet.
• Keep hands, long hair, clothing, ties, jewelry and loose
items away from the feed opening and shred outlet.
• Do not use the shredder for anything other than its
intended purpose. Never use it to shred cloth, plastic,
cardboard or any hard material that will cause damage to the shredder blades.
Hose & cap assembly
Oil reservoir bottle
Power switch
continued on the next page