ANDELI AJR3-1030 Руководство по эксплуатации - Страница 4
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Контроллер ANDELI AJR3-1030. ANDELI AJR3-1030 15 страниц.
Печатать страницу2. Installation and wiring
2-3 Wiring
Please pay attention to the following points when wiring. Refer to diagram 2-3-1
for basic wiring
The power supply must be connected with terminals 1L1, 3L2 and 5L3 of main circuit, no phase
requirement. If there is any wrong connection, it will damage the soft starter.
The ground terminals must be earthed finely, so that it can avoid electric shock or fire accident,
and it can reduce the noise.
The two terminals of lead should be compressed joint to assure high reliability in connection.
Diagram 2-3-1
Diagram of
basic wiring
Equipped with bypass electromagnetic contactor
Equipped with
circuit breaker
（MCCB）
Or
Leakage
circuit breaker
（ELCB）
Power
L1
1 L1
supply
3-phase
L2
3 L2
380V
50/60HZ
L3
5 L3
FU
01
Full voltage
output
N
02
或
A1
A2
L1
Time delay
03
output
(Programmable)
04
05
Fault output
06
RS485 communication
Main circuit
（KM）
1
2
3
4
5
6
A2
2T1
B2
4T2
M
C2
6T3
G
+DC12V
K3
Instantaneous stop
07
Ue=
100%
Stop
08
Start
09
K2
Common port
10
K1
10
11
Analog output
(DC 0-20mA)
12
Control circuit
-3-
2. Installation and wiring
2-4 Wiring of main circuit and earth terminal
Table 2-4-1 Function of main circuit and earth terminal
Terminal mark
Terminal name
1L1, 3L2, 5L3
Power supply input of main circuit
2T1, 4T2, 6T3
Output connection of soft starter
Bypass connection
A2, B2, C2
Grounding terminal of soft
G
starter
(1) Power supply input terminals of the main circuit (1L1, 3L2, 5L3)
Power supply terminals 1L1, 3L2 and 5L3 of main circuit connect with 3-phase power supply
through protective circuit breaker or leakage circuit breaker. It is not necessary to consider the
connecting phase sequence.
Please do not adopt the ON/OFF control method (power supply of main circuit) to start or stop
the soft starter, you should electrify the soft starter first, and then make use of the control terminal
that on the soft starter or the RUN and STOP keys to run or stop the machine.
Please do not connect with single-phase power supply.
(2) Output terminals of soft starter (2T1, 4T2, 6T3)
Connect the output terminals of the soft starter with 3-phase motor in correct phase sequence.
If the rotation direction of the motor is wrong, you can exchange the connection of any two pha-
ses of 2T1, 4T2 and 6T3.
The output side of the soft starter can not be connected with capacitor and surge absorber.
When the wire between soft starter and motor is very long, the distributed capacitance among
the wire will produce high frequency current, it may cause phenomenon like over current and
trip, more leakage current, low accuracy of current display, etc. Therefore, we suggest that the
wire for motor connection should be less than 50m.
(3) Bypass connection (A2, B2, C2)
The bypass connection terminals A2, B2 and C2 must be connect with the electromagnetic by-
pass contactor, otherwise, the soft starter would be burned. After the soft starter is started, the
power device of major loop (silicon controlled rectifier) exits, meanwhile, the bypass electrom-
agnetic contactor works, and the motor runs normally, pay attention to the phases, they cannot be
wrong connected.
(4) Grounding terminal of soft starter (
In order to reduce noise and for safety consideration, the grounding terminal
starter must be firmly earthed. In order to avoid electric shock and fire accident, the metal enclo-
sure and frame of the electric equipment should comply with the national electric requirements.
Confirm that the input phase number and rated input voltage of the soft starter should be accord
with the phase number and voltage value of the AC power supply.
The AC power supply can not connect with the output terminals (2T1, 4T2, 6T3, A2, B2, C2)
The bypass electromagnetic contactor must be connected, and the phase sequence can be wrong
connected.
Danger
Otherwise, there may be accidents happen.
Description
Connect with 3-phase power supply
Connect with 3-phase motor
Connect with bypass electromagnetic contactor
The grounding terminal of the case
of soft starter should be earthed firmly
G)
G of the soft
-4-