Ativa OD690XA Инструкция по эксплуатации

Просмотреть онлайн или скачать pdf Инструкция по эксплуатации для Измельчитель бумаги Ativa OD690XA. Ativa OD690XA 1 страница. Product manual

Печатать страницу

OPERATION:

6 sheets

Sheet Capacity

20lb. bond paper*

Operating Instructions

0.22 in. x 1.84 in. pieces

Installation

Paper Shred Size

5.6 mm x 46.8 mm pieces

Operation

Paper Entry Width

8.66 in. / 220 mm

Warning

Troubleshooting

Credit Card Capacity

1 at a time

Maintenance

Limited Product Warranty

Voltage

120V~60Hz 2.0A

ONE FOLDED SHEET OF PAPER EQUATES TO 2 SHEETS OF PAPER

Heavier paper, humidity or other than rate voltage may reduce capacity.

INSTALLATION:

Using the switch located on the unit, select one of the following settings by sliding the switch either

left or right. (FIGURE 2)

FIGURE 1

Never shred plastic (except credit cards), any hard materials, continuous forms,

newsprint, or anything with adhesives including labels and envelopes.

Mount the shredder securely to the rim of the waste basket. (FIGURE 1)

While this shredder will shred staples, it is recommended that you remove them whenever possible in

A socket-outlet should be near the equipment and be easily accessible.

order to extend the life of your shredder.

Connect the power cord to any standard 120 volt AC outlet.

Only shred credit cards by feeding them vertically within the designated area.

ATTENTION:

Never feed more than one credit card at a time.

This model includes a built-in safety interlock mechanism, which requires the shredder to be correctly

mounted on to the included wastebasket. Located on the back center of the shredder, next to the power

cord, there is a curved flap-like shape that must FIT OVER THE OUTSIDE matching ridge of the

wastebasket. (FIGURE #1) THE SHREDDER WILL NOT OPERATE UNLESS IT IS PROPERLY

MOUNTED AS PICTURED!

It is not designed to operate with any other wastebaskets. An activation switch located on the head unit

automatically shuts off the shredder when it is lifted or removed. The supplied wastebasket activates this

switch, which allows the shredder to be operable. Lining the wastebasket with a plastic bag will interfere

and may keep the shredder from functioning.

Caution: Crosscut shredders have very sharp exposed blades on the underside.

Use care when mounting the shredder on the wastebasket.

FIGURE 2

Auto: This setting allows the shredder to be automatically started by inserting paper into the

shred opening. Always feed the paper in as straight as possible. When the paper has

passed through, the shredder will automatically stop. (FIGURE 2)

Off: This setting turns off all features of the shredder. For safety reasons, we recommend that

you leave the shredder in the "Off" position whenever the shredder is unattended or

not in use. (FIGURE 2)

Rev: In the unlikely event of a paper jam, the reverse setting can be used to help clear the

cutters of paper that has not passed through. Never attempt to clear a jam by using

the reverse function until you have emptied the wastebasket. (FIGURE 2)

WARNING:

TROUBLESHOOTING PAPER SHREDDERS:

The shredder does not work at all.

Avoid touching the document

Do not spray or keep any aerosol

a) Make sure the unit is plugged in and that the outlet it is plugged into is in good working order.

feed opening with hands.

products in or around shredder.

b) In the event that the shredder is run continuously for too long and the motor overheats, a thermal

overload switch will automatically shut the power off. If this happens, move the switch to the off

Product is not intended for use by

Avoid loose clothing or jewelry

position for 30 minutes or more before continuing.

children (product is not a toy).

touching the document feed opening.

c) If using a plastic bag to line the wastebasket, please remove it since this may be the cause of the

shredder to not operate properly.

d) The activation switch of the shredder is located near the center of the feed slot. Be sure to feed directly

Do not insert foreign objects into

Avoid getting hair near the

into the center area to trigger the machine (especially applies to smaller pieces of paper or

the document feed opening.

document feed opening.

credit cards).

e) Make sure the head unit portion of the shredder is

correctly seated onto the included wastebasket with the

words and icons facing towards you. The head unit is

- RISK OF FIRE. Never use any petroleum based or flammable oils or lubricants in or around the

particularly designed to work only with the integrated

machine as some oils can combust causing serious injury.

wastebasket. Shredders are equipped with a safety

- NEVER dispose of flammable chemicals or materials that have come into contact

interlock mechanism, which prevents the unit from

with flammable chemicals (for example, nail polish, acetone, gasoline) in the shredder basket.

working when the head unit is lifted, removed, or

- Never shred plastic (except credit cards), any hard materials, continuous forms,

accidentally knocked over. Located on either the back

newsprint, or anything with adhesives including labels and envelopes.

center, next to the power cord, is a "curved flap-like shape" that MUST FIT OVER THE OUTSIDE

- A socket-outlet should be near the equipment and be easily accessible.

matching ridge of the wastebasket. The shredder will not operate unless the head unit is properly

- Always turn the shredder off and unplug the power cord from the AC outlet before cleaning it,

mounted as pictured.

moving it, or emptying the waste basket.

- Never let the wastebasket become full. This will lead to shredded material being pulled back up into

the shredder and cause jams.

The shredder runs in "Rev" mode but not in "Auto" mode.

- Never place the shredder near water or any heat source.

a) While in "Auto" mode, the motor will not start running until paper is inserted into the

- Keep wastebasket emptied so that the shredder output is not impeded.

feed slot. Set the unit to "Auto" and insert paper to be shredded. It is normal for the motor to run for

- Do not use the shredder if the power cord is damaged in any way.

a moment after setting it to "Auto" but it should stop until paper is inserted. The trigger that activates the

- Do not attempt to service this product yourself as doing so may expose you to sharp cutting blades

shredder in Auto mode is located directly in the center of the slot. If the paper you are inserting is narrow,

and/or electricity and will void the manufacturers warranty.

it may not be hitting the switch. It is possible that the trigger, which activates the shredder, has become

- Never try to clean or clear the shredder blade.

blocked with paper. Insert an index card, directly in the center of the feed slot, and apply force. This

will usually clear any paper blocking the switch and force the switch closed.

How to clear a paper jam in the shredder:

a) Switch the shredder over into reverse mode. While in reverse, the shredder will back up to loosen the

jammed paper. If required, you may need to tug on the paper to effectively clear the machine. When

jammed paper is loosened or removed, switch back to the Auto-On mode to continue shredding.

b) With stubborn situations where the reverse function does not help, you may loosen the jammed paper

with shredder oil (cooking oil is acceptable, nothing aerosol). Start by drizzling oil into the blades

where the paper is jammed. Let it soak for about 30 minutes to completely saturate. Return the

shredder back to Auto-On mode. If required, a rigid sheet of cardstock (old greeting card, folded file

folder, or a sheet torn from a cereal box) can be fed into the shredder to help push the jammed

paper through.

LIMITED PRODUCT WARRANTY:

MAINTENANCE:

Keep your shredder running with ultimate reliability with the following Ativa shredder supplies:

Shredder Lubricant Sheets

To quickly and conveniently maintain shredder blade lubrication, use a Shredder Lubricant Sheet once

a month.

This limited warranty covers the original purchase of new product used for normal commercial, personal

or household use. Swinton Avenue Trading, Inc. (SAT) warrants its products will be free from defects in

Shredder Oil

materials and workmanship (normal wear and tear excepted), for one (1) year from the date of

Apply a bead of this lubricant across a sheet of paper once a month and shred it. It helps to keep the

purchase, except as provided below. SAT, at its option, will replace with a comparable product, free of

shredder blades operating well over many years of use.

charge, any product which fails under normal use as a result of such defect. This warranty does not

apply to damage caused by fire, accident, negligence, misuse, improper cleaning or other

circumstances not directly attributable to manufacturing defects.

Oil the shredder blades every month with recommended lubricant sheets (Office Depot item number

340-960) or oil (Office Depot item number 285-661).

Additionally, the cutting cylinders are warranted for a period of 5 years from the original purchase date

Do not spray or keep any aerosol products in or around shredder.

and will be replaced without charge for material or labor if found by SAT to be defective.

DO NOT USE CANNED AIR ON SHREDDER.

Proof of purchase is required in the form of a receipt (copy or original) to validate warranty. If you do

CLEANING:

not have a copy of your store receipt and paid using a check or a major credit card, a copy can be

• ALWAYS UNPLUG THE SHREDDER BEFORE CLEANING!

obtained from Office Depot's receipt retrieval department at

• Only clean the shredder by carefully wiping the unit with a dry soft cloth or towel.

• Do not clean or immerse shredder in water. Having the unit wet may result in

If SAT chooses to provide a refund for such product, it will be fulfilled in the form of an Office Depot

damage or malfunction to the electrical components. If the shredder happens to get

Merchandise card. Claims fulfilled in this manner take approximately 90 days to process.

wet, be sure to completely dry the unit immediately with a cloth or towel.

• Never use anything flammable to clean the shredder.

SAT PROVIDES THIS LIMITED WARRANTY IN LIEU OF ALL OTHER WARRANTIES EITHER EXPRESS OR

This may result in serious injury or damage to the product.

IMPLIED. EXPRESSLY EXCLUDED ARE ALL WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR

MERCHANTABILITY. SAT'S SOLE OBLIGATION AND THE USER'S EXCLUSIVE REMEDY UNDER THIS

WARRANTY SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT AT SAT'S SOLE DISCRETION AND

COST, OF PRODUCT OR COMPONENTS.

IN NO EVENT SHALL SAT, ITS AFFILIATES, SUBSIDIARIES OR PARENT COMPANIES BE RESPONSIBLE

FOR CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES ARISING OUT OF A CLAIM OF

DEFECTIVE PRODUCT EVEN IF SAT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

SOME STATES OR PROVINCES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION

OF INCIDENTIAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY

TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE

OTHER RIGHTS WHICH MAY VARY BY STATE OR PROVINCE.

THIS WARRANTY APPLIES ONLY TO THE U.S. AND CANADA.

Return Instructions

Please call 1-877-777-HELP (1-877-777-4357) for warranty service or product support.

Swinton Avenue Trading, Inc.

Limited Product Warranty

1-800-721-6592.