Bosch GBM 13-2 RE Руководство по эксплуатации - Страница 8

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Сверло Bosch GBM 13-2 RE. Bosch GBM 13-2 RE 12 страниц.

Печатать страницу

Technical Data

Rotary drill
Article number
Rated power input
Output power
No-load speed
– 1st gear
– 2nd gear
Rated speed
– 1st gear
– 2nd gear
Rated torque (1st/2nd gear)
Spindle collar dia.
Speed preselection
Speed control
Right/left rotation
Maximum drilling diameter
(1st/2nd gear)
– Steel
– Wood
– Aluminium
Max. screw dia.
Chuck clamping range
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries, these val-
ues can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.

Declaration of Conformity

We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the
provisions
of
the
98/37/EC.
Dr. Egbert Schneider
Senior Vice President
Engineering
22.11.2006, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
1 609 929 K97 • 25.1.07
GBM ...
PROFESSIONAL
0 601 ...
W
W
rpm
rpm
rpm
rpm
Nm
mm
mm
mm
mm
mm
mm
kg
directives
89/336/EEC,
Dr. Eckerhard Strötgen
Head of Product
Certification
10
10 RE 10 SRE 10-2 RE
135 0..
135 5..
137 5..
450
450
420
220
220
220
2000
0–2200
0–2600
–
–
1300
0–1300
0–1600
–
–
6.0/–
6.0/–
6.0/– 9.5/5.0 11.5/6.0 11.5/6.0
43
43
–
–
–
–
10/–
10/–
10/–
25/–
25/–
25/–
13/–
13/–
13/–
–
–
1–10
1–10
1–10
1.5
1.5
/II
/II
Assembly
Auxiliary Handle (GBM 13-2/
GBM 13-2 RE) (see figure A)
Operate your machine only with the auxiliary
handle 11.
The auxiliary handle 11 can be set to any position for a
secure and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary
handle 10 in anticlockwise direction and set the auxil-
iary handle 11 to the required position. Then tighten the
wing bolt 10 again in clockwise direction.
Adjusting the Drilling Depth
The required drilling depth X can be set with the depth
stop 12.
Loosen the wing bolt for the depth stop adjustment 9
and insert the depth stop rod into the auxiliary handle
11.
The knurled surface of the depth stop 12 must face
upward.
13-2 13-2 RE
168 5..
169 0..
500
550
270
285
0–1150
1000
–
0–2100
1900
0–800
550
–
0–1500
1000
43
43
43
–
–
–
–
10/6
13/8
25/15
32/20
13/8
20/12
6
–
–
1–10
1–13
1.5
1.7
1.9
/II
/II
/II
169 5..
550
285
0–1000
0–1900
0–550
0–1000
43
13/8
32/20
20/12
–
1–13
1.9
/II
English | 17