Bosch GDR 180-LI Руководство по эксплуатации - Страница 9
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Сверло Bosch GDR 180-LI. Bosch GDR 180-LI 18 страниц. Professional
Также для Bosch GDR 180-LI: Оригинальное руководство по эксплуатации (21 страниц)
Печатать страницу
To remove the battery (3), press the release button (4) and
pull the battery forward and out of the power tool. Do not
use force to do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Changing the Tool (see figures A and B)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Bosch Power Tools
When working with an application tool, ensure that
u
the application tool is connected securely to the tool
holder. If the application tool is not securely connected to
the tool holder, it can come off during operation.
Inserting
GDR 180-LI:
Pull the locking sleeve (2) forward, guide the application tool
into the tool holder (1) up to the stop and release the locking
sleeve (2) to lock the application tool.
Only use screwdriver bits with ball catch (9) (DIN 3126-
E6.3). Other screwdriver bits (11) can be inserted using a
universal bit holder with ball catch (10).
GDX 180-LI:
Slide the application tool (12) onto the square drive of the
tool holder (1).
Due to the way the system operates, the application tool
(12) will move around slightly in the tool holder (1); this has
to
no effect on the function/safety.
Removing
Pull the locking sleeve (2) forward and remove the applica-
tion tool.
Operation
Method of Operation
The tool holder (1) (with the application tool) is driven by an
electric motor via a gear and impact mechanism.
Capacity
The working procedure is divided into two phases:
60−100 %
Screwing in and tightening (impact mechanism in action).
30−60 %
The impact mechanism is activated as soon as the screwed
5−30 %
connection runs tight and load is therefore put on the motor.
The impact mechanism then converts the power of the mo-
0−5 %
tor to steady rotary impacts. When loosening screws or nuts,
the process is reversed.
Starting Operation
Inserting the Battery
Set the rotational direction switch (5) to the centre position
Capacity
to protect the power tool from being switched on accident-
80−100 %
ally.
Push the charged battery (3) into the base of the power tool
60−80 %
from the front until the battery is securely locked.
40−60 %
Set the rotational direction (see figure C)
20−40 %
The rotational direction switch (5) is used to change the ro-
5−20 %
tational direction of the power tool. However, this is not pos-
0−5 %
sible while the on/off switch (6) is being pressed.
Right rotation: To drive in screws and tighten nuts, press
the rotational direction switch (5) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (5) through to the right
stop.
English | 9
1 609 92A 713 | (21.11.2022)