Electrolux ICON E36GC75DSS1 Руководство по установке - Страница 6
Просмотреть онлайн или скачать pdf Руководство по установке для Варочная панель Electrolux ICON E36GC75DSS1. Electrolux ICON E36GC75DSS1 8 страниц. 30" electric rangetop
Также для Electrolux ICON E36GC75DSS1: Технические характеристики (1 страниц), Руководство по эксплуатации и уходу (20 страниц)
Печатать страницу
The supply line should be equipped with an approved
shutoff valve. This valve should be located in the same
room as the cooktop and should be in a location that
allows ease of opening and closing. Do not block access
to the shutoff valve. The valve is for turning on or
shutting off gas to the appliance.
Grounding
Instructions
IMPORTANT Please read carefully.
For personal safety, this appliance must be properly
grounded.
The power cord of this appliance is equipped with a 3-
prong (grounding) plug which mates with a standard 3-
prong grounding wall receptacle (see Figure 7) to
minimize the possibility of electric shock hazard from the
appliance.
Preferred Method
Grounding type
wall rece
Do not, under
any circumstances,
CUt, remove,
or bypass the
grounding
prong.
\,
/
Figure 6
Open the shutoff valve in the gas supply line. Wait a few
minutes for gas to move through the gas line.
Check for leaks. Leak testing
of the appliance shall
be conducted according to the manufacturer's
instructions.
After connecting the cooktop to the gas
supply, check the system for leaks with a manometer. If
a manometer is not available, turn on the gas supply and
use a liquid leak detector (or soap and water) at all
joints and connections to check for leaks.
Power supply
cord with 3-prong
grounding plug.
Figure 7
The wall receptacle and circuit should be checked by a
qualified electrician to make sure the receptacle is
properly grounded.
F_
Do not use a flame to check for leaks
from gas connections.
Checking for leaks with a flame
may result in a fire or explosion.
Tighten all connections if necessary to prevent gas
leakage in the cooktop or supply line.
Check alignment
of valves after connecting the
cooktop to the gas supply to be sure the cooktop
manifold pipe has not been moved.
Disconnect this cooktop and its individual
shutoff
valve from the gas supply piping system during any
pressure testing of that system at test pressures greater
than 1/2 psig (3.5 kPa or 14" (35.6 cm) water column).
Isolate the cooktop from the gas supply piping
system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psig
(3.5 kPa or 14" (35.6 cm) water column).
Electrical
Requirements
120 volt, 60 Hertz, properly grounded branch circuit
protected by a 15 amp circuit breaker or time delay fuse.
Do not use an extension
cord with this cooktop.
Where a standard 2-prong wall receptacle is installed, it
is the personal responsibility and obligation
of the
consumer to have it replaced by a properly grounded 3-
prong wall receptacle.
Do not, under any circumstances, cut or remove the
third
(ground) prong from the power cord.
Disconnect electrical supply cord from
wall receptacle before servicing cooktop.
6
Cooktop
Installation
1. Visually inspect the cooktop for damage.
2. If you are installing the optional Stainless Steel
backsplash, first fix it at the back of the cooktop using
the screws supplied with the kit and follow the
instructions attached.
Go to step 3, If you are not installing the Optional
Stainless Steel backsplash.
3. Set the cooktop into the countertop cutout.
NOTE: Do not use caulking compound; cooktop should
be removable for service when needed.