Andrew CommScope-S Инструкция по применению - Страница 2

Просмотреть онлайн или скачать pdf Инструкция по применению для Инструменты Andrew CommScope-S. Andrew CommScope-S 2 страницы. Preparation tool

Печатать страницу

Instructions for Use

CommScope -S Preparation tool

for 1 1/4" and 1 5/8" annularly corrugated cables LDF6-50, AVA6-50 and AVA7-50

Attention: Preparation tool must be handled and used with great care, blades

are extremely sharp! It is recommended to use working gloves.

1. Snap in matching collet segment. Corrugation has to be close to blade 1.

2. Release clamping screw with enclosed allen key and adjust blade 2 acc.

to installation instructions for the connector by turning the adjusting spindle.

Observe scale for correct position of blade 2. Lock clamping screw.

3. Insert and lock in place clamping device (only for 1 1/4" cables required)

4. Close clamping lever until the gap on the clamping lever side is about 2 mm.

Insert cable end into cable clamp and tighten the adjusting screw until the

cable clamps.

Attention: Set adjusting screw only when changing the cable type or

clamping is insufficient.

5. Remove the cable jacket with a knife.

6. Insert cable into the preparation tool in a way that at least a half corrugation

pitch protrudes over blade 1. The corrugation crest has to fit into the

corrugation of collet segment. Clamp cable with clamping lever.

7. Turn feed handwheel (left hand thread) manually until blade 1 is situated

close over the cable.

Cut cable outer conductor with blade 1 by turning the rotor with the crank

clockwise. After separation, the feed handwheel (left hand thread) can be

turned manually until blade 1 is just before the inner conductor.

Cut cable completely by turning the rotor with the crank clockwise. At the

same time the cable jacket is notched with blade 2.

8. The cable is trimmed, when the cable inner conductor is completely cut.

Then open blade housing by turning back the feed handwheel (left hand

thread) and remove cable.

9. Follow the installation bulletin for the connector to prepare the cable.

10. Insert centering pin of the flaring tool into the cable inner conductor. Turn the

tool to flare cable end. Ensure, that the spike of the flaring tool is positioned

under the cable outer conductor.

Replacement of worn blades: The blades supplied are made of hardened

steel. Therefore no commercially available cutting blades can be used.

Replace worn blades only with genuine parts.

Caution: Blades are extremely sharp!

11. When changing blade 1 both screws have to be released by a few turns

with the added Allen key. Once the new blade has been installed, the

screws have to be locked again. Observe position of cutting edge! Take

care that blade 1 is positioned symmetrically to the screws.

12. When changing blade 2 first remove blade 1 to get access to the locking

screw for blade 2 . The screw has to be released by a few turns with the

added Allen key. Once the new blade has been installed, the screw has to

be locked again.

部件名称/Component

Name

铅/Pb 汞/Hg 镉/Cd 六价铬/Cr 6+ 多溴联 f /PBB

金属零件/metal parts

These instructions are written for qualified and experienced personnel. Please study them carefully before starting any work. Any liability or responsibility for the results of improper or unsafe installation practices is disclaimed. Please respect valid environmental regulations for assembly and waste disposal.

Studieren Sie bitte sorgfältig vor Beginn der Montage diese Anleitung, die für geschultes und qualifiziertes Personal erstellt ist. Bei unsachgemäßer Montage ist eine Haftung bzw. Gewährleistung ausgeschlossen. Bitte beachten Sie bei Montage und Entsorgung die geltenden Umweltschutzbestimmungen.

Ces instructions sont écrites pour des personnes qualifiées et expérimentées. Il est nécessaire de bien les lire avant de commencer l'installation. Notre responsabilité ne pourra être engagée si l'installation n'a pas été faite en conformité avec nos instructions. Prière de respecter les règles d'environnement en application

pour le montage.

Estas instrucciones estan dirijídas a personal calificado y con la debida experiencia. Por favor léalas cuidadosamente antes de iniciar su trabajo. No asumimos ninguna responsabilidad derivada de instalaciones impropias ó sin las adecuadas medidas de seguridad. Por favor respete las regulaciones para proteccion ambiental y desecho de desperdicios.

Estas instruções são dirigidas ao pessoal qualificado e com a devida experiência. Por favor leia-as atentamente antes de começar a tarefa. Não assumimos nenhuma responsabilidade devido a execução da instalação de maneira imprópria ou sem as adequadas medidas de segurança. Por favor respeite os regulamentos

válidos de meio ambiente para a montagem e remoção de resíduos.

本安装说明为合格及有经验的操作人员所写. 请在安装之前仔细阅读. 任何不恰当或不安全的安装所引起的责任, 都将不予受理. 并请遵守关于装配件及废物弃置的有效环保条例.

Andrew Wireless Solutions

Customer Service 24 hours

U.S.A., Canada, Mexico:

for HELIAX® AVA Cables call 1-800-255-1479

for HELIAX® SFX, FXL Cables call 1-888-235-5732

U.K.: 0800 250055 Brazil: +55-15-2102-4000

Other Europe: +44 592 782 612

有毒有害物质或元素/Toxic or Hazardous Substances and Elements

www.commscope.com

Visit our Web site at www.commscope.com or contact your local Andrew Wireless Solutions representative for more information.

Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by ® or TM are registered trade-

marks or trade-marks, respectively, of CommScope. This document is for planning purposes only and is not intended to

modify or supplement any specifications or warranties relating to Andrew Wireless Solutions products or services.

Achtung: Absetzwerkzeug mit großer Sorgfalt handhaben und gebrauchen,

die Klingen sind äußerst scharf! Das Tragen von Arbeitshandschuhen wird