Atlantic Ultraviolet MIN-9 Руководство пользователя - Страница 16

Просмотреть онлайн или скачать pdf Руководство пользователя для Системы фильтрации воды Atlantic Ultraviolet MIN-9. Atlantic Ultraviolet MIN-9 20 страниц. Germicidal ultraviolet water purifiers
Также для Atlantic Ultraviolet MIN-9: Руководство пользователя (16 страниц), Руководство пользователя (16 страниц)

Печатать страницу

EPLACEMENT OF

SAFETY EQUIPMENT REQUIRED TO PERFORM TASK

CAUTION: Broken Quartz is SHARP. It is recommended that protective goggles and gloves are worn when handling.

WARNING: Disconnect power to water purifier.

•

For 120v 50/60Hz version using ballast no. 10-0508B, remove the ground connector from the chamber,

and go to the next step

•

For 230v 50/60Hz version using ballast no. 10-0504A, go to next step.

Shut off water supply to water purifier via inlet and outlet shut off valves and drain chamber, if possible.

Follow the steps in "Quartz Sleeve Installation, Cleaning or Replacement" to remove lamp and quartz sleeve.

Unscrew static gland nuts from each end of the chamber. Avoid striking quartz sleeve with static gland nut.

Remove Teflon

washer and o-ring from both ends of quartz sleeve. Teflon

gland nut. If so, remove Teflon

CAUTION: Carefully remove as much of the broken quartz sleeve as possible, from each end of the chamber.

7. To remove fragments of quartz sleeve, hold the purifier vertically and shake. The quartz fragments will break and drop out

of the purifier through the gland fitting. Flush water through chamber being careful to remove all quartz fragments from the

interior of the chamber.

8. Carefully discard all pieces of the broken quartz sleeve.

9. Align the end of the quartz sleeve with the gland fitting of the chamber.

10. Carefully slide the quartz sleeve into the chamber, guiding it through the gland fitting. NOTE: Use care to keep the quartz

sleeve parallel to the chamber, angling the quartz sleeve in any direction could result in the breakage of the quartz sleeve.

11. As the quartz sleeve nears the far end of the chamber, support the quartz sleeve by inserting your finger through the far end

gland fitting and into the quartz sleeve. This will minimize the possibility of breaking the quartz sleeve as it passes through

the gland fitting.

12. Center the quartz sleeve in the chamber, making sure the quartz sleeve protrudes an equal distance past each threaded gland

fitting, of the chamber.

13. Re-install o-rings, Teflon

Tighten static gland nuts firmly by hand only, DO NOT USE HAND TOOLS. Tightening with hand tools is likely to cause

quartz sleeve to break.

14. When all connections are complete allow water to enter the water purifier at a low flow rate until the purifier is pressurized.

With the purifier pressurized, it should be checked for leaks.

15. If no leaks occur, reinstall lamp, following the steps in "LAMP INSTALLATION OR REPLACEMENT" section.

ISPOSAL OF

ERCURY

Germicidal ultraviolet lamps, like standard fluorescent lamps contain small amounts of mercury. Mercury added lamps

should not be placed in the trash. Dispose of properly. For further information regarding the disposal and recycling of

lamps containing mercury, along with Federal and State requirements visit http://www.lamprecycle.org. Product Data

Sheets for germicidal ultraviolet lamps can be found in the "PDF Library for Ster-L-Ray

Lamps" section of http://www.ultraviolet.com.

ROKEN

UARTZ

LEEVE

washer from static gland nut before proceeding.

washers, and static gland nuts. Be sure o-rings are placed on quartz sleeve before Teflon

DDED

AMPS

washer will some times remain within the static

Germicidal Ultraviolet

washer.