Atlantic Ultraviolet Sanidyne 40-06374B Установка, эксплуатация и обслуживание - Страница 11

Просмотреть онлайн или скачать pdf Установка, эксплуатация и обслуживание для Аксессуары Atlantic Ultraviolet Sanidyne 40-06374B. Atlantic Ultraviolet Sanidyne 40-06374B 20 страниц. Germicidal ultraviolet portable area sanitizer

Печатать страницу

aniDyne

rime

The Sanidyne

Prime Remote has two methods of controlling the unit; the Keypad Controller (Shown in Figure 2) and the

Hand-held Remote Controller (Shown in Figure 3). These two controls mirror each other; treatment times entered into Keypad

Controller will appear on the Hand-held Remote Controller and vice versa.

sing tHe

eyPaD

Setting Treatment Time on the Keypad is done using the HOURS and MINUTES buttons which are located on the top of

the unit. (See Figure 1 for location) Selecting the up or down facing arrows located on the keypad in line with the HOURS

or MINUTES button will either increase or decrease the hours or minutes. The hours can be set between 0 and 24, and

the minutes can be set from 1 to 59. (Example of one hour and five minutes would appear as 01:05 on the Treatment Time

Display). Since the Keypad Controller will no longer be viewable once the treatment time begins, it is recommended that the

Hand-held Remote Controller be fully charged and powered before this time and be in possession of the operator at all times.

2. Determining the proper treatment times for your specific location can be done by using the "Recommended Treatment Time

for Room Size" chart (Figure 4 on Page 13).

3. Once the choice of time has been displayed on the Keypad controller, select the START/STOP button to begin and leave the

Operation Area immediately. Make sure that the Hand-held Remote Controller is kept in possession of the operator during the

Treatment Time.

Once you select the START / STOP button an audible exit alarm will begin to sound and the Sanidyne

Remote will begin counting down from 1:30 seconds to allow all inhabitants to leave the area before the UV treatment

begins. Additionally, the word "PrEP" will begin flashing on the Keypad and the Occupancy Sensors located on the

top of the unit (Shown on Figure 1) will begin to operate at this time, providing an additional safety area around the

unit. As an additional safety feature, if the sensors detect movement close to the Sanidyne

less than 30 seconds remain on the countdown time, the Sanidyne

seconds more to leave the Operation Area.

Occupancy Sensors do not protect the entire Operation Area of the Sanidyne

circumstances should this sanitizer be permitted to operate with humans, plants, or animals present in the Operation Area.

4. Outside the Operation Area the Treatment Time can be viewed on the Hand-held Remote Controller. Once the treatment time

has expired the unit will turn off the STER-L-RAY

The word "DONE" will begin flashing on the Keypad Controller on the top of the unit.

sing tHe

anD

HelD

The Hand-held Remote Controller provides further detailed information on the Sanidyne

recommended to review the Hand-held Remote Controller Overview section of this manual to become familiar with the display

which is shown in Figure 3.

The Hand-held Remote Controller can operate the Sanidyne

imperative that the operator make a visual inspection of the Operation Area to ensure it is clear of all humans, plants, or

animals before proceeding.

1. Setting Treatment Time on the Hand-held Remote Controller is done by holding a finger on the display face, directly on the

words Treatment Time until the screen changes to a scroll bar. Next scroll the numbers up or down, characters on the left are

hours, characters on the right are minutes. Positioning the desired treatment time in the center row. (Example of one hour and

five minutes would appear as 01:05 on the Treatment Time Display) When times are positioned correctly, select DONE on the

bottom of the scroll bar to input your Treatment Time choice.

Determining the proper treatment times for your specific location can be done by using the "Recommended Treatment Time

for Room Size" chart (Figure 4 on Page 13).

Once the choice of time has been displayed on the Hand-held Remote Controller, select the start button to begin and leave the

Operation Area immediately. Make sure that the Hand-held Remote Controller is kept in possession of the operator during the

Treatment Time. (Remote Controller Instructions Continued on Page 12)

emote

Peration

ontroller to

emote

ontroller to

reatment

imes

Prime Remote will automatically reset giving 30

Germicidal Ultraviolet Lamps and it is now safe to return to the area.

reatment

Prime

Prime Remote when

Prime Remote. Under no

imes

Prime Remote. Therefore it is

Prime Remote remotely, thus it is