Electrolux RH36WC60GSA Руководство по установке, уходу и эксплуатации - Страница 17
Просмотреть онлайн или скачать pdf Руководство по установке, уходу и эксплуатации для Вентиляционная вытяжка Electrolux RH36WC60GSA. Electrolux RH36WC60GSA 21 страница. 30" and 36" free standing range hood
Также для Electrolux RH36WC60GSA: Заводской каталог деталей (4 страниц), Заводской каталог деталей (4 страниц), Каталог деталей (4 страниц)
Печатать страницу
i
Specia
functions
Clock program.,ing
The clock can be reprogrammed at any time except during an active timed function.
•
The clock can be displayed in a twelve hour format and valid clock times are from 1:00 to 12:59.
•
The clock can be reprogrammed pressing the "Timer' button for 5 seconds, and after, the clock can be
adjusted with the "A"and
"V'_butt°ns'
Colon ":'" will flash indicating clock programming mode.
•
The user can have minute increments / decrements of 1 minute, but if the user keep pressing the "A"/
'V'
buttons for more than 1 second, the increments / decrements will be of 5 minutes.
During this option the control will round to the nearest 5 minutes.
,,
•
The user can finish on reprogramming the clock pressing the Timer button.
•
After 1 minute of no button pressed the control will accept the programmed clock time and will add one
minute to the set clock.
Grease filter saturation
alarm
•
After thirty fan functional hours, the display will show "Grease Filter" if the fan is active.
When this icon is shown in the display, the grease filters installed are required to be washed.
To reset the grease filter saturation alarm the user must press the "_"
button for 5 seconds, after this
action the icon "Grease filter" is not displayed, and the hood has the normal display operation.
Charcoal
filter saturation
alarm {Recirculating
accessories)
•
After one hundred and twenty functional hours of the fan, the display will show "Charcoal Filter" if the fan
is active. When this icon flashes on display, the charcoal filters installed are required to be replaced or
reactivated.
To reset the charcoal filter saturation indication the user must press the "V"
button for 5 seconds, after
this time the icon "Charcoal filte¢' is not displayed and the hood has the normal display operation.
Audible signal activation
and deactivation
•
The audible signals can be activated or deactivated pressing the "Light" button for 5 seconds.
If the audible signal is activated, a tone must sound and the "Snd" symbol must appear on the display for
2 seconds.
If the audible signal is deactivated, the "Snd" symbol must appear on the display for 2 seconds and no
tone must sound.
Charcoal filter inclusion and exclusion {Recirculating accessories)
•
The charcoal filter inclusion or exclusion can be set by pressing the "V"
and "_"
buttons at the same
time for 5 seconds.
The Inclusion or exclusion of charcoal filter must be selected while the lamps and the motor are OFF.
When the charcoal filter has been excluded, the charcoal filter alarm is disabled.
Heat
sensor
The control is equipped with a heat sensor that will turn on the blower at second speed if excessive heat
occurs (over 158 ° F or 70°0) surrounding the control area.
If the blower is OFF or if it is operating at first speed, the blower will be set automatically to second speed,
the display shows the word "CARE"to indicate that heat sensor has detected an excessive heat.
During this state, the user may raise the blower speed to third speed but can not decrease the speed.
When the temperature level on the hood drops to normal, the blower will operate in the setting defined by
the user before the alarm occured.