Bose Panaray LT3202 III Mid/High Справочное руководство - Страница 5
Просмотреть онлайн или скачать pdf Справочное руководство для Динамики Bose Panaray LT3202 III Mid/High. Bose Panaray LT3202 III Mid/High 40 страниц. Panaray lt series iii
Также для Bose Panaray LT3202 III Mid/High: Руководство по установке (32 страниц), Руководство по эксплуатации (27 страниц)
Печатать страницу
Mounting Guidelines
WARNING: The Panaray
permanent or seasonal use. Such mountings, typically in overhead locations, involve risk of personal injury if either
the mounting system or the loudspeaker attachment fails. Installation of the mounting system must be performed in
accordance with all applicable building codes including local codes. Consult the local authority before installing this
product.
CAUTION: Use only graded hardware. Fasteners should be SAE Grade 5 or ASTM designation A354, Grade BC
minimum. Unmarked machine fasteners should not be used for mounting system assembly, as there is no way to
determine their physical properties. Do not use an M10 fastener; although it is very similar to an SAE
they are not interchangeable. M10 washers may be used in place of
CAUTION: The fasteners should be tightened using torque not to exceed 50 pounds.inch (5.6 Newton-meters).
Over-tightening the fastener could result in irreparable damage to the cabinet and create an unsafe assembly.
CAUTION: The fastener should be long enough to engage no fewer than 16 threads of the attachment point . Using a
fastener that is too short provides inadequate holding power and may strip the mounting threads, resulting in an unsafe
assembly. Confirm that at least 16 full threads are engaged in your assembly.
CAUTION: Do not attempt to alter the threaded attachment points. Do not attempt to re-thread the attachment points to
accommodate any other thread size or type; doing so will compromise the safety of the installation while permanently
damaging the loudspeaker.
®
LT Series loudspeakers must be attached to brackets or other mounting surfaces for
The LT loudspeaker installation requires the use of either Bose
products. While Bose Corporation cannot be held responsible for the proper design and
use of non-Bose mounting systems, we offer the following information and guidelines for
the permanent installation of your Panaray LT loudspeakers:
•
Obtain your mounting system from a reputable manufacturer. Select a system design
that works for your loudspeaker and its intended use.
•
Before using a custom-designed mounting system, have a licensed professional
engineer review the design and fabrication for structural integrity and safety in the
intended application.
•
The threaded attachment points on the top, bottom, and sides of each loudspeaker
have an SAE
3
/
-16 inch thread with at least 18 usable threads.
8
•
Lock washers or a locking compound intended for hand disassembly (such as
Loctite 242) should be used for a vibration resistant assembly.
•
Use a safety cable, separately attached to the cabinet, at a point not in common with
the load-bearing attachment points of the mounting system to the loudspeaker. This
is recommended even if not required by local regulation. If you are unfamiliar with the
proper design, use, and purpose of a safety cable, consult a licensed professional
engineer or a rigging professional.
•
Additional loudspeakers may be suspended below the Panaray LT loudspeaker
provided that:
•
It employs all 8 threaded-insert hang points on the top and bottom to
fly and suspend the loudspeakers.
•
The total weight of suspended loudspeakers and the Panaray LT
loudspeaker does not exceed the working load limit (WLL) listed
below:
®
LT 3202
-III Loudspeaker = 395 lb (179 kg)
LT 9402
-III Loudspeaker = 261 lb (118 kg)
TM
LT MB24-III Loudspeaker = 520 lb (236 kg)
Safety Information
LT 4402
®
-III Loudspeaker = 299 lb (135 kg)
®
LT 9702
-III Loudspeaker = 381 lb (173 kg)
3
/
-inch washers.
8
®
or non-Bose mounting
3
/
-16,
8
5