Dromida kodo hd Руководство пользователя - Страница 3
Просмотреть онлайн или скачать pdf Руководство пользователя для Дроны Dromida kodo hd. Dromida kodo hd 4 страницы.
Печатать страницу
BLADE REPLACEMENT
NOTE: Rotor blades must be installed as shown.
• Carefully pry off the
blade using a fl at head
screwdriver.
• Rotor blades are marked
with an A or B.
• Yellow rotor blades are
front and black are rear.
• Match the A and B
blades to this drawing
to insure that the
replacement blades are
in the correct locations.
SENSOR CALIBRATION
It is normal for the Kodo HD to require
minor corrections while hovering. If
the quad has a strong tendency to
drift in one direction, the sensors
may need calibration.
1. Power up and link the controller
and the Kodo HD.
2. Place the quad on a level surface.
3. Hold both sticks in the lower right corners. When the LED on the quad starts to fl ash
rapidly, release the sticks but do not move the Kodo HD until the LED is steady again.
MOTOR REPLACEMENT
1. Remove the rotor blade from the motor.
2. Remove the blade guard from the motor housing.
3. While holding the motor locking tab open, place the motor shaft on a solid surface
and push down on the arm to force the motor up and out of the motor housing.
4. Remove the wires from the brackets on the arms and unplug the assembly from
the control board.
5. Before installing the new motor, make sure that the wires are the same color and
are installed in the same positions in the connector.
TROUBLESHOOTING
PROBLEM: KODO will not stay level or drifts while hovering.
SOLUTION: (1) Calibrate the sensors – see the Sensor Calibration section.
(2) Check the rotor blades and motors for damage. A common
problem is lint wrapped around the motor shaft.
PROBLEM: Red controller LED light flashing after linking.
SOLUTION: Replace with new AAA batteries.
PROBLEM: The Kodo HD will not respond to the controller.
SOLUTION: (1) Relink the controller and the Kodo HD.
(2) Make sure the flight battery is fully charged.
PROBLEM: Unable to flip but the KODO is flying.
SOLUTION: Battery voltage is low and needs to be charged.
PROBLEM: Will not take off.
SOLUTION: (1) Check the rotor blades for proper installation.
(2) Battery is not fully charged.
(3) Check motors and props for damage.
PROBLEM: Drone is shaking.
SOLUTION: Check the canopy, chassis, motors and rotor blades for damage.
SAFETY PRECAUTIONS
Follow these safety precautions when operating this or any model drone.
•
Adult supervision required.
•
Do not touch the spinning blades or fly over another person's head.
•
Keep your face and body as well as all spectators away from the rotors
whenever the battery is connected.
•
Stay clear of buildings, trees and power lines. AVOID flying in or near crowded
areas. DO NOT fly close to people, children or pets.
•
Maintain a safe pilot-to-drone distance while flying.
•
Your KODO drone should not be considered a toy, but rather a small, working
model. If not operated correctly, the model could possibly cause injury to you
or spectators and damage to property.
•
Do not alter or modify the model, as doing so may result in an unsafe or
unflyable model.
•
You must check the operation of the model before every flight to insure that
the model has remained structurally sound.
CAUTION: Changes or modifications to this product not expressly approved by
the party responsible for compliance may void the user's authority to operate the
equipment.
BATTERY PRECAUTIONS
The KODO is equipped with a rechargeable 3.7V LiPo battery. Please pay
attention to the following cautions for safe use:
•
Parental guidance is recommended when installing batteries.
•
Only use the included charger with the flight battery.
•
Do not attempt to use this charger with NiCd or NiMH battery packs.
•
Do not attempt to use a damaged battery.
•
This product contains a LiPo battery. Must be recycled or disposed of properly.
•
Do not leave the charger unattended while charging. Disconnect the battery
and unplug the charger immediately if either becomes hot! However, it is
normal for the charger to get warm.
•
Disconnect the battery from the charger and carefully move the battery to a
fireproof location if the battery begins to swell or smoke!
•
Never allow the battery temperature to exceed 140° F [60° C].