ELEKON BATSCANNER STEREO Руководство

Просмотреть онлайн или скачать pdf Руководство для Датчики безопасности ELEKON BATSCANNER STEREO. ELEKON BATSCANNER STEREO 2 страницы.

Печатать страницу
BATSCANNER
STEREO
Manual
Thank you for purchasing Elekon AG's BATSCANNER STEREO.
The BATSCANNER STEREO is an easy to use bat detector. It converts the ultrasonic bat calls
into an audible frequency with the „mixer" principle (heterodyne). What makes the BATSCANNER
STEREO unique is that the mixing frequency is adjusted and displayed automatically for the
detected bat species. Thus, the different bat species can be heard without manual tuning and its
main frequency can be seen easily.
1
Notes
Instructions for safe use:
Children must be supervised whilst using this product. Do not disassemble or modify
the product. Please read this manual carefully and entirely before using this product.
Warning:
The microphones and the speaker (openings) as well as the entire BATSCANNER
STEREO must be protected from rain and generally from liquids and harsh
environmental influences.
Batteries:
For the operation 3×1.5 V AAA Alkaline batteries (LR03) are placed in the battery
compartment on the back of the BATSCANNER STEREO. (Note the polarity when
inserting batteries). Old or defective batteries must be removed and disposed
properly. Depending on the battery type an operation of about 20 – 25 hours is
reached. Rechargeable batteries down to 3×1.2 V with the same size can also be
used.
Sensitivity:
BATSCANNER STEREO primarily is a headphones device. If operating without
headphones indoors, in cars, near electronic devices or close to surfaces, etc. at high
volume a feedback loop through the speaker can occur. This is expressed in
whistling
noise.
Because
of
the
automatic
BATSCANNER STEREO such effects can not be suppressed completely without
reducing the sensitivity. Remedy: use in "free" environment (distance from obstacles)
and possibly take back the volume or use headphones.
2
Package Contents
en
• BATSCANNER STEREO device incl. 3×1.5 V AAA batteries
• Headphones
• Wrist strap
• This manual
3
Features
• Automatic detects bat calls and tunes frequency accordingly
• Stereo output to precisely locate bats
• Speaker or headphones operation
• Optional manual frequency tuning
3.5mm Jack for headphones
• Can be used with regular or rechargeable batteries
Microphones
4
Using BATSCANNER STEREO
Display
1. Plug in the headphones for stereo operation.
2. Power on the device by pressing the
Button
3. The device goes into automatic mode and sets the initial frequency to 48kHz. The device
–
Button
now listens to incoming bat calls and adjusts the frequency accordingly. The bat calls are
transformed into audible range and output to headphones or speaker.
+
Button
4. Press the
5. If no button is pressed for >30min. the device turns off to save battery.
Speaker
5
Switching modes
1. Press the + and – button simultaneously to toggle between automatic and manual mode.
2. The current mode is displayed by the left LED bar.
5.1
Automatic mode
The mixing frequency is adjusted and displayed automatically for the detected bat species. Thus,
the different bat species can be heard without manual tuning and its main frequency can be seen
Elekon AG
easily. The direction (L/R) of the triggering source is displayed if detected.
Cheerstrasse 16
1. Use the + and – buttons to increase or decrease the volume.
CH-6014 Luzern
2. Press the
www.batscanner.ch
5.2
Manual mode
The mixing frequency can be adjusted manually. Only bat species in the set frequency range can
be heard.
1. Use the + and – buttons to increase or decrease the frequency.
2. Press the
3. To change the volume, switch to automatic mode first.
6
Check batteries
Battery voltage has to be 2.5 – 4.5 V.
Please note: If using rechargeable batteries, the operation time may be shorter.
1. BATSCANNER STEREO is switched off.
2. Press and hold the
7
Change options
For special use cases it may be needed to change device options:
•
Auto off (Ao):
•
Dots (do):
•
Lower frequency limit:
•
Upper frequency limit:
1. BATSCANNER STEREO is switched off.
2. Press and hold the
3. Use the + and – buttons to change auto off option (Ao).
4. Press the
5. Use the + and – buttons to change the direction detection option (do).
6. Press the
7. Use the + and – buttons to increase or decrease the lower frequency limit.
frequency
adjustment
of
the
8. Press the
9. Use the + and – buttons to increase or decrease the upper frequency limit.
10.Press the
-Button (On).
-Button for >1s to switch off the device (OFF).
-Button to reset the frequency to 48kHz.
-button to reset the frequency to 48kHz.
-Button for >3s to display the actual battery voltage (b4.3).
Enable (Ao1)/Disable (Ao0) 30min auto off timer
Enable (do1)/Disable(do0) left/right detection option
Set lower frequency limit of automatic detection
Set upper frequency limit of automatic detection
and the + buttons for >3s to enter options mode (Opt).
-Button to switch to the next option.
-Button to switch to the next option.
-Button to switch to the next option.
-Button to store the options (sto). The device turns off.