DryBuddy DryBuddy1 Руководство - Страница 2

Просмотреть онлайн или скачать pdf Руководство для Система безопасности DryBuddy DryBuddy1. DryBuddy DryBuddy1 2 страницы.

Печатать страницу

DryBuddy1 Specifications

Sensor

13.5 mm

32 mm

6 mm

17 mm

DryBuddy1 Specifications

(Con't)

• Contains an audio alarm which can be as loud as 93 dB

at 20 cms. (8 "), 89 at 40 cms. (16"), 86 dB at 60 cms. (24").

Please adjust to a suitable loudness level using the Volume

control in the Receiver.

• Certifications: FCC XXXXXXXXXX; CE

ZZZZZZZZZZZZZZZ

• RoHS compliant.

FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitly approved by

manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

The device has been evaluated to meet general RF exposure requirement. The device

can be used in portable exposure condition without restriction.

DryBuddy1 Specifications

Sensor

• Can be attached to standard cotton briefs using the

patented magnetic attachment system, or

• Can be attached to optional DryBuddy wetness sensing

briefs which contain patented redundant wiring. These

briefs provide a reliable and very large wetness sensing

area.

48 mm

• Uses a unique coding system so that it can only be used with a

DryBuddy1 Receiver.

• Must be synchronized with a DryBuddy1 Receiver.

• Typical transmission distance is up to three (3) meters

or ten (10) feet to the Receiver. The actual transmission

distance depends upon object and materials between the

Sensor and Receiver.

• Sealed unit with non-replaceable battery.

• Designed and tested to trigger (transmit) over 2,000 times

under typical and proper use.

• When triggered, the sensor will remain inactive for 2

42 mm

minutes before it can be triggered again.

• Certifications: FCC RHU-DBFLS02; CE

ESTBA1508012214R

• RoHS compliant.

Note: Once a Sensor is triggered (or shorted) to transmit an alert

signal, the sensor will remain inactive for two (2) minutes and cannot

be triggered again till this inactive period is over.

Caution when Using the

• The DryBuddy alarm is intended for use as a bed-wetting

and enuresis alarm by children of age five and older, or as

recommended by a medical authority. It can be used by older

patients as a urine sensor and wetness alarm and as an

incontinence alarm.

• The DryBuddy system is a medical device and should be

treated as such. Do not use roughly or damage.

• Do not use as a potty training aid for babies, toddlers and

young children.

• Make certain that no parts of the DryBuddy or sensor are put

in the mouth for any reason as this could cause choking or

other harm.

• Observe all sanitary precautions to keep the sensor clean and

the alarm parts clean and dry.

• Do not use the sensor for more than one user without

thorough cleaning.

• Do not strike the magnetic sensor or cap on hard surfaces or

make them hot as this can reduce magnetism.

• The DryBuddy system is designed to sense urine or salty

water. It is less effective in sensing plain water.

DryBuddy1 Specifications

(Con't)

Receiver

DryBuddy1

51 W. Fairmont Avenue, Suite 2

(Con't)

Weight (without batteries):

• Uses two (2) replaceable AAA alkaline batteries.

• Uses a unique coding system so that it can only be used

with a DryBuddy1 Sensor.

• Must be synchronized with a DryBuddy1 Sensor.

• Typical reception distance is up to three (3) meters or ten

(10) feet from the Sensor. The actual transmission distance

depends upon object and materials between the Sensor

and Receiver.

Good Things Happen with DryBuddy

Raising the Standards for Mobility,

Privacy, Performance and Value.

Enuresis Solutions, LLC

Advena Ltd.

Savannah, GA 31406 USA

Tower Business Centre, 2nd Flr.,

912-352-8854

Tower Street, Swatar, BKR 4013 Malta

[email protected]

The DryBuddy1 is designed in USA. Assembled in China.

�

EC REP