DSC The NEW FORCE 2 F2-212 Инструкции по установке - Страница 2

Просмотреть онлайн или скачать pdf Инструкции по установке для Датчики безопасности DSC The NEW FORCE 2 F2-212. DSC The NEW FORCE 2 F2-212 2 страницы. F2-210 series, pir/microwave motion detector

Печатать страницу

DSC The NEW FORCE 2 F2-212 Инструкции по установке

Use the optional DM-W Wall Mount and DM-C Ceiling Mount

brackets to solve difficult placement

problems.

The DM-W and DM-C

mount to either the wall or ceiling and

allow for full vertical and horizontal

positioning of the motion detector -

the detector can be tilted up or down

and rotated through 90° to obtain the

best position for optimal coverage.

The New Force 2 has been designed

to be fully compatible with the DM-W

and DM-C brackets. Contact your

DSC distributor for more information.

IMPORTANT NOTE: Maximum

detection coverage occurs when the

FORCE 2 is mounted at the height

specified in the mounting instructions and the mounting surface

is vertical. If this cannot be achieved with a mounting bracket,

then detector coverage may be less than specified.

WIRING

Once the detector is mounted in the desired location, connect the

wiring as shown below.

following optional features.

FORCE 2 - OPTIONS

F2-210

F2-210 ....................... 'A' Alarm contact only

F2-210

F2-211

F2-211 ....................... 'A' Alarm contact & Tamper switch

F2-211

F2-212 ....................... 'C' Alarm contact & Tamper switch

F2-212

NOTE: Contacts are shown in the non-alarm state with power

applied to the detector.

POWER

12V

30mA

ALARM

Contacts Rated

100mA @ 24V

GND +12

10Ω

OPTION

POWER UP

Upon application of power, the alarm indicator will be illuminated

for 60 seconds to indicate the unit is warming up. During this

period, the alarm relay is held in its normal non-alarm state. After

the 60 second warm-up period, the alarm indicator will go out and

the unit will respond to motion in the protected area.

ALARM INDICATOR ON/OFF JUMPER J1

With Jumper J1 OFF, the alarm indicator will turn on each time the

unit goes into alarm. With J1 ON, the alarm indicator is disabled.

WALK TESTING

It is imperative that the unit be thoroughly walk tested after mounting

to ensure that coverage extends over the desired area.

Once coverage has been confirmed, Jumper J1 may be set to the

ON position to disable the alarm LED indicator.

IMPORTANT NOTE: Upon installation, the unit should be

thoroughly tested to verify proper operation. The end user should

be instructed on how to perform walk tests, and should perform a

walk test at least once per year.

DM-C

Ceiling Mounting Bracket

DM-W

Wall Mounting Bracket

Note that various models have the

TAMPER

Contacts Rated

100mA @ 24V

OPTION

COMPONENT LOCATIONS

PIR LENS

The PIR lens is mounted with the textured

side facing in (smooth side facing out).

Note that the long lens elements are at the

top when the lens is properly positioned.

Ensure the lens is properly seated, and

that the lens holder is securely snapped

into place.

LIMITED WARRANTY

Digital Security Controls Ltd. warrants that for a period of five years

from the date of purchase, the product shall be free of defects in

materials and workmanship under normal use and that in fulfilment

of any breach of such warranty, Digital Security Controls Ltd. shall,

at its option, repair or replace the defective equipment upon return

of the equipment to its repair depot. This warranty applies only to

defects in parts and workmanship and not to damage incurred in

shipping or handling, or damage due to causes beyond the control

of Digital Security Controls Ltd. such as lightning, excessive

voltage, mechanical shock, water damage, or damage arising out

of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and

is and shall be in lieu of any and all other warranties, whether

expressed or implied and of all other obligations or liabilities on the

part of Digital Security Controls Ltd. Digital Security Controls Ltd.

neither assumes, nor authorizes any other person purporting to act

on its behalf to modify or to change this warranty, nor to assume

for it any other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any

direct, indirect or consequential damages, loss of anticipated

profits, loss of time or any other losses incurred by the buyer in

connection with the purchase, installation or operation or failure

of this product.

WARNING: Digital Security Controls Ltd. recommends that the

entire system be completely tested on a regular basis. However,

despite frequent testing, and due to, but not limited to, criminal

tampering or electrical disruption, it is possible for this product

to fail to perform as expected.

IMPORTANT INFORMATION

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY DIGITAL

SECURITY CONTROLS LTD. COULD VOID THE USER'S AUTHORITY TO OPERATE

THIS EQUIPMENT.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT

CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

Toronto, Canada

Tech Line: 1-800-387-3630

Web Site: www.dscgrp.com

is a trademark of Digital Security Controls Ltd.

TOP

PIR LENS

29002410 R002