DSC PC5108 Инструкции по установке

Просмотреть онлайн или скачать pdf Инструкции по установке для Блок управления DSC PC5108. DSC PC5108 2 страницы. 8 zone expander

Печатать страницу

Limited Warranty Digital Security Controls Ltd. warrants that for a period of twelve months from the date of

Limited Warranty

purchase, the product shall be free of defects in materials and workmanship under normal use and that in

fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repair or replace

the defective equipment upon return of the equipment to its factory. This warranty applies only to defects in

parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes

beyond the control of Digital Security Controls Ltd., such as lightning, excessive voltage, mechanical

shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other

warranties, whether expressed or implied, and of all other obligations or liabilities on the part of Digital

Security Controls Ltd. This warranty contains the entire warranty. Digital Security Controls Ltd. neither

assumes, nor authorizes any other person purporting to act on its behalf to modify or to change this

warranty, nor to assume for it any other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct or indirect or consequential damages,

loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the

purchase, installation or operation or failure of this product.

Warning: Digital Security Controls Ltd. recommends that the entire system be completely tested on a

Warning:

regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or

electrical disruption, it is possible for this product to fail to perform as expected.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your

authority to use this equipment.

This equipment generates and uses radio frequency energy and if not installed and used properly, in strict

accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has

been type tested and found to comply with the limits for Class B device in accordance with the specifications in

Subpart "B" of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference

in any residential installation. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause interference to television or radio reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Re-orient the receiving antenna

•

Relocate the alarm control with respect to the receiver

•

Move the alarm control away from the receiver

Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

•

If necessary, the user should consult the dealer or an experienced radio/television technician for additional

suggestions. The user may find the following booklet prepared by the FCC useful: "How to Identify and Resolve

Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing Office,

Washington D.C. 20402, Stock # 004-000-00345-4.

Toronto, Canada

Technical Support: 1-800-387-3630

Printed in Canada 29004817 R001

Installation Instructions

The PC5108 module can be used to add up to 8 additional hardwired

zones to the PC5010, PC5015 & PC5020 control panels (see the control

panel Installation Manual for complete installation instructions).

Specifications

• Module Current Draw: 35 mA

• Auxiliary Current: 100 mA (PTC protected - fuseless design)

Terminal Description

TAM - This can be used to tamper the cabinet in which the PC5108 is

mounted. Connect a normally closed (NC) switch across TAM and BLK. If

the tamper is not being used connect a piece of wire across TAM and BLK

to remove the trouble condition.

PC51O8

8 Zone Expander

Version 2.O