DSE DK-WP2 Руководство пользователя - Страница 2

Просмотреть онлайн или скачать pdf Руководство пользователя для Камера безопасности DSE DK-WP2. DSE DK-WP2 4 страницы. Camera and vcr in wall clock

Печатать страницу

OWNER'S MANUAL

Once exhausted the memory capacity of the micro SD card, the device will erase the recorded

files by overwriting the oldest new recorded files.

In motion recording, DVR records video lasting 1 minute. In continuous recording it generates

files for 10 minutes.

Shooting Position

DK-WP2 recovers from a place near the front hole at 6 o'clock which provides an upright image

with the clock normally hung on the wall.

The angle is not adjustable for which it is necessary to locate the clock a suitable position to

provide a good angle of view.

IR Remote Control

DK-WP2 check with the infrared remote control that should be pointed toward the receiver placed

at 3. The button function as follows:

A - ON / OFF

B - Start recording continuous C - I shoot

D - Start recording motion E - Opens the OSD menu on the

external monitor

F - Playing back recorded movies on an external monitor G - OK button in the OSD

H / I - Buttons move in the OSD

Recording in motion detection

The recording in motion detection is the most widely used because in this DK-WP2 mode records

only in the moment in which occurs a movement in the field of view lens. Each movement creates

a recording of a minute, after which, in the absence of movements, the DVR returns to rest

conditions waiting for a new intrusion.

If you use the DK-WP2 with mains power, it starts recording in motion mode automatically when it

is connected to power.

First, to become familiar with the device,

experience

operation.

CURRENT RECORD IN MOTION

1 - Enter the DK-WP2 power adapter into the socket

2 - The DVR will automatically turn on and the signal is green LED lights up for 1-2 seconds.

3 - The Motion recording starts automatically. The red LED flashes 3 times slowly. This signals

the start of the motion recording.

4 - To stop motion recording, press the D button on the remote. The LED returns to solid green,

indicating that the appliance is on standby waiting for commands

5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the

shutdown.

RECORD IN MOTION A BATTERY

DK-WP2 camera with VCR in wall clock

this

guy

DSE srl - Digital Surveillance Equipment - www.dse.eu

1 - After turning off the DVR as seen in step 5 above, disconnect the power supply of the DK-WP2

from the socket.

2 - Press the A button on the remote to turn on the DVR. The Indicator LED lights green for 1-2

seconds.

3 - The Motion recording starts automatically. The red LED flashes 3 times slowly. This signals

the start of the motion recording.

4 - To stop motion recording, press the D button on the remote. The LED returns to solid green,

indicating that the appliance is on standby waiting for commands

5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the

shutdown.

continuous Recording

Continuous recording takes up a lot of storage space, but it is sometimes necessary when, for

example, the uninterrupted audio recording is important, even if there is no motion in front of the

lens. In continuous recording, the DVR records Factory consecutive files from 3 minutes (can be

changed in configuration). To continuously record proceed as follows:

1 - Allow the start of the motion recording as above. The red LED flashes three times slowly.

2 - Stop motion recording, press the D button on the remote. The LED returns to solid green,

indicating that the appliance is on standby waiting for commands.

3 - Press the B button to start the recording continues. The LED flashes green for 2 times slowly.

This signals the start of the continuous recording.

4 - To stop continuous recording, press the B button on the remote again. The LED returns to solid

green, indicating that the appliance is on standby waiting for commands

5 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the

shutdown.

Take pictures

DK-WP2 can also take pictures based on commands from the remote control. The photos are

saved in JPG format with 2560x1920 resolution (5MP) To take pictures, proceed as follows:

1 - Allow the start of the motion recording as above. The red LED flashes three times slowly.

2 - Stop motion recording by pressing the D button on the remote. The LED returns to solid green,

indicating that the appliance is on standby waiting for commands.

3 - Press the C button to take the picture. The LED flashes red for the first time. This signals that

the photo was taken and stored in memory. The solid green LED returns at last to report the

stand-by condition.

4 - Press the A button to turn off the DVR. The red LED flashes for 3 times quickly to confirm the

shutdown.

Viewing files on PC

To review and manage files recorded by the DVR

you can use a computer and a

Document: DK-WP2-1I6

Page: 2