Attwood 7200 Series Инструкции по установке

Просмотреть онлайн или скачать pdf Инструкции по установке для Морское освещение Attwood 7200 Series. Attwood 7200 Series 2 страницы. 12-volt anchor/masthead light

Печатать страницу

Anchor/Masthead Light

12-Volt: 7200 and 7400 Series

24-Volt: 7250 and 7450 Series

Installation Instructions

SAVE THESE INSTRUCTIONS

Form Number 69394 Rev. B

FEATURES

Attwood 3-mile (4.8 km) Anchor/Masthead Lights consist of anodized

aluminum poles with lightweight heads. Horizontal and vertical bases

allow light pole to be adjusted and locked within a 180 arc.

Lights provide a 3-mile, 225 forward running light and 2-mile all-round

anchor light. For power-driven boats boats up to 65.6 feet (20 meters).

Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all

applicable standards as tested by Imanna Laboratory, Inc., December

17, 2003. Lights use 8-watt festoon lamp, #9230 (for 12-volt systems)

or #910409 (for 24-volt systems).

CAUTION

To prevent personal injury, disconnect the power source when installing

or servicing any electrical product. Remove vessel from water when

using any 120 VAC power tools.

Lens can be HOT and can melt or scorch fabric. When folded down,

turn light OFF and be sure lens does not touch anything.

REQUIRED FOR INSTALLATION

• Cordless drill; 1/8" and 3/8" (3 and 10mm) bits

• Marine-grade non-silicone sealant

• Phillips screwdriver

• Two #10 pan head stainless steel screws

• 3-position switch (OFF/ON/ON)

• Fuse holder and fuse: 2-amp (for 12-volt systems) or 1-amp

(for 24-volt systems)

• 16-gauge wire

• Marine-grade wire connectors for 16-gauge wire

MOUNTING LOCATION

CAUTION

Install light so that fin (Figure 3) is TOWARD STERN and aligned on

the fore/aft centerline of the vessel (within 1 ). If not properly aligned,

lights will not shine in required fore/aft arc.

Base must pivot on the fore/aft centerline and be mounted on a surface

that allows a 360 arc of unobstructed light visibility. (Figure 1)

Bases are available for mounting on vertical or horizontal surfaces.

Release the cam-lock adjustment handle to fold light or adjust to

vertical position.

Figure 1

INSTALLATION INSTRUCTIONS

Change Base Type (If Required)

Packaged versions of the Anchor/Masthead Light are shipped with

the vertical base installed. To switch to the horizontal base:

1. Carefully remove the cam-lock screw and oblong washer. Set aside

for reinstallation (Figure 2).

2. Pivot the base axle out of its socket. Note position of the 3 wires in

the base slot. Remove the vertical base.

3. Insert wires through slot of the horizontal base. Install in reverse order.

For windshield, on horizontal

Figure 2

STEP 1

Cam-lock Screw

and Oblong Washer

04-07

Install Light

1. Release cam-lock adjustment handle and adjust light to vertical

position. (Figure 3)

2. Place light in selected position. BE SURE THAT FIN IS ALIGNED

TOWARD STERN.

3. Use provided adaptors, if necessary, to allow installation on

angled windshields.

Figure 3

FWD

4. Using the base as a template, mark the two mounting hole

locations and one wire access hole. (Figure 4)

CAUTION

Position wire access hole carefully, especially on aluminum boats,

so that wires do not contact the hull.

5. Remove light. Drill two 1/8" (3mm) pilot holes for #10 screws. Drill

one 3/8" (10mm) wire access hole.

6. Bring two 16-gauge (+) wires and one 16-gauge (-) wire up through

access hole. DO NOT connect power to switch until you read

CONNECT POWER TO SWITCH.

7. Use marine-grade waterproof crimp connectors to connect blue

wire to one (+) positive lead from 3-position switch; connect gray

wire to second (+) lead. Connect (-) negative source to black wire

and route to (-) negative terminal on battery.

8. Fasten light to deck with two #10 stainless steel pan head screws.

DO NOT OVERTIGHTEN.

STEP 2

STEP 3

Vertical

Horizontal

Base

Feed Wires Thru

Fin

(AFT)

Locked

Unlocked

Vertical Mount

AFT

PORT

Fin

(AFT)

Locked

Unlocked

Horizontal Mount

AFT

PORT

Socket

Axle

STBD