ADDER ADDERLink INFINITY 3000 Краткое руководство по эксплуатации
Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Удлинитель ADDER ADDERLink INFINITY 3000. ADDER ADDERLink INFINITY 3000 2 страницы.
Также для ADDER ADDERLink INFINITY 3000: Быстрый старт (2 страниц)
Печатать страницу
Initial configuration
ALIF3000 units depend upon ADDERLink INFINITY Manager (AIM) for almost all of their
configuration. As a new ALIF3000 unit is added to a network it must be in its factory default mode so
that AIM can engage with it and begin managing its resources. If an ALIF3000 is not in factory default
mode, please see the center pages.
To connect and configure an ALIF3000
1 Connect the ALIF3000 to an AIM-controlled network using either of the SFP ports via a suitable
CATx or fiber SFP module.
2 Connect the necessary peripheral devices to the ALIF3000 and apply power to it via the supplied
power adapter.
3 The OLED screen on the front panel will provide status information:
ALIF 3000
ALIF 3000
–––––––––––––––
–––––––––––––––
Searching...
Connecting...
You should see the message progress from Searching... to Connected.
4 Log into AIM as an administrator and locate the new ALIF3000R entry within the Receivers section.
5 Click the
icon on the ALIF3000R entry to configure the device. Please see the AIM user guide for
further details.
www.adder.com/en/kvm-solutions/adderlink-infinity-3000
www.adder.com
© 2020 Adder Technology Limited • All trademarks are acknowledged.
Part No. MAN-QS-ALIF3000-ADDER_V1.0
ALIF 3000
–––––––––––––––
Connected
Full user details and setup instructions can be found at:
ADDERLink
Welcome
This quick start guide covers some of the key points of the
ADDERLink™ INFINITY 3000 (ALIF3000) unit, which has
been created to address the growing requirement to connect
users to both physical and virtual machines. Using standard
VDI (Virtual Desktop Infrastructure) protocols - which are
built-in; the ALIF3000 delivers seamless access to legacy KVM
systems as well as Virtual Machine (VM) sources, from the
same common console.
Dual DisplayPort
®
video outlets provide support for a
single 2560x1600 display or two at a maximum 1920x1200
resolution (60Hz refresh).
Gigabit connections
The ALIF3000 receiver has two SFP ports located on its rear
panel, which can accommodate a range of fiber or copper
networking modules, as suits your installation. Each port
can be connected to a separate gigabit fiber (or copper)
network to permit access to a wider range of systems. A
third network port (RJ45) is also provided to allow separate
access, where necessary, to a corporate network to gain the
VM hosting configuration data. All three connections are
securely isolated within the ALIF3000 to prevent any cross
contamination between networks.
Important
ALIF3000 can ONLY be connected as part of an ADDERLink INFINITY system that is administered by
an ADDERLink INFINITY Manager. See rear page for Initial configuration details.
It is important that each ALIF3000 is set to its factory default settings, otherwise it will not be
discovered by the AIM server. If the standard settings have been changed in a previous installation, you
merely need to perform a manual factory reset on each unit. Please see the center pages.
Minimum versions
In a mixed ALIF installation, ensure that the various
components have the following software versions:
• AIM server:
v4.11
• ALIF100T-DVI:
v4.07
• ALIF100T- VGA: v4.08
• ALIF1xxx:
v4.9
• ALIF2xxx:
v4.9
• ALIF3xxx:
v1.0
• ALIF4xxx:
v3.0
INFINITY 3000
™
Quick Start
ALIF3000
Network
ALIF TX
Legacy KVM
Virtual
system(s)
machines
Full user details and setup
instructions can be found
at www.adder.com/en/
kvm-solutions/adderlink-
infinity-3000
Please read the supplied safety
instruction leaflet before use.
switch