Ducati SW400 FC Руководство - Страница 9
Просмотреть онлайн или скачать pdf Руководство для Открыватель ворот Ducati SW400 FC. Ducati SW400 FC 11 страниц.
Печатать страницу
DUCATI
How to install the actuator
actuator's model
see diagram on page
HC 312................................page 10
HC 412................................page 11
HC 512................................page 12
HC 612................................page 13
HC 418................................page 14
HC 518................................page 15
HC 618................................page 16
SW 400...............................page 17
SW 400T.............................page 18
EVO 700.............................page 19
EVO 700T...........................page 20
EVE 900.............................page 21
EVE 900 T..........................page 22
VERY IMPORTANT ADVICES:
WARNING: The actuator should preferably have a angle of incidence to the
closed gate and therefore not be perfectly parallel to the gate wing (see page 8).
This will keep your gate well locked when the gate is closed, as the actuator will
push the gate wing to the end stop with major force.
WARNING: make sure not to use the full actuator stroke as the gate wing must
stop by pressing on a mechanical end limit (fixed on the ground or FC integrated
limit) before the actuator reaches the end of it's own stroke travel (see page 8).
In case of telescopic actuator it allows to keep the telescopic tube more guided
when it is extroflexed, ensuring greater solidity.
WARNING: In Gate opening towards inside the property ( PULL-TO-OPEN)
measures A & B shown in each actuator's diagram as well on page 9 are extremely
important as they shall determinate the gate opening angle and speed as well
as actuator thrust strenght. The shorter travel of the actuator's stroke is used, the
greater the gate opening speed will be.
In general, smaller the A and B measurements,will result in higher gate
opening speed.
Attention, it is recommended not to use a too high opening speed to avoid
unwanted bumping rebounds at the end of the maneuver.
Where possible increase measure B to reduce speed.
Important! to allow a linear movement of the automation A & B measures should be
similar.
30
Warning: on double wing gates use same A & B measure on both sides.
To determine the most suitable mounting position, proceed as follows:
- Measure the depth of the the Post/ pillar column where your gate is installed to
(measure from thecenter hinge to the inner edge of the column)
-After the depth of your post has been measured, compare it to maximal dimensions
A and B indicated in the table of your actuator's model.
Warning: "B" measure is the sum of the depth of your pillar to cente hinge +
lenght of fixing brackets supplied.
Warning: the supplied post fixing brackets offer several holes choice.
- Select the hole where to fix the actuator to, accordingly to A & B meassures limits.
- If necessary, cut away the excess of the bracket.
Warning: in some cases it will be necessary to get tailor-maid post fixing brackets
made by a blacksmith (for example in the case of round columns).
- Now determine the mounting position of the plate on the column, taking into
account that the dimension B determines the maximum opening angle and the door
opening speed. If this angle does not match your needs, you should re-adjust quote
A and quote B so that they are similar.
Warning: Before securing the rear bracket and keeping the actuator in a perfectly
horizontal and balanced position, perfectly horizontal supporting the engine, verify
that the front fixing point of the actuator coincides with a solid and robust cross of
the gate. Make sure that the actuator is mounted at a minimum height above the
ground ( min.15 cm are recommended) so that it is easy to operate the manual
unlocking system.
Warning: in case your structure dimension do not allow to comply with the A& B
dimensions stated in the actuator table & diagram (ex. large masonry pillar), you will
need to carry out masonry works to allow the correct instalaltion of the gate opener
Fix the bracket to the pillar/ coloumn/ fence post
Each actuator model is provided with specific fixing brackets.
Mark middle of post bracket slots on pillar/ coloumn/ fence post.
Fix the bracket on the pillar. Use suitable fastening bolts anchors (not supplied)
suitable to the pillar construction material (iron post / concreete, bric or stone pillar).
FIx the actuator to the post bracket:
Fasten the actuator to the bracket of the rear fixing with the pin and seal ring
- for EVE actuators see pag..23
- for "HC" actuators see pag.24
- for "SW" & EVO actuators see pag.25