Anywire ASLINKAMP LA-F1011 Руководство по эксплуатации - Страница 6
Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Усилитель Anywire ASLINKAMP LA-F1011. Anywire ASLINKAMP LA-F1011 11 страниц. Fiber amplifier
Также для Anywire ASLINKAMP LA-F1011: Руководство по эксплуатации (11 страниц)
Печатать страницу[Transmission Line Connection]
The transmission line from the ber ampli er master unit is connected
to the transmission line of the AnyWireASLINK master unit.
This terminal is 4-wire (isolated) type. To use this terminal, connect the
DP, DN, 24V and 0V pins.
■Description of attached wires
Wire color
Description
Red
DP: Transmission line (+)
Black
DN: Transmission line (-)
Green
24V: Unit drive power supply (+)
0V: Unit drive power supply (-)
White
[Connection via link connector (example)]
■Power supply to the entire system
Master unit
DP, DN
24V, 0V
FK4-125-100
LP4-WR-10P
To LP4-WW-10P,
pressure-bonding
transmission line link
connector
■Local power supply
Master unit
DP, DN
Local power supply
24V, 0V
FK4-125-100
LP4-WR-10P
To LP4-WW-10P,
pressure-bonding
transmission line link
connector
■Link connector pin assignment
Pin No. Description Wire color
1
DN
Black
2
DP
Red
3
0V
White
4
24V
Green
[Master unit
transmission wire color]
DP : Red
DN : Black
24V : Green
0V : White
[Master unit
transmission wire color]
DP : Red
DN : Black
24V : Green
0V : White
The LP connector (link connector) is a
connector that integrates male and female
terminals.
It makes it easy to "connect" and "branch" the
line simply by connecting two connectors of
the same type.
[Connection of Fiber]
Fiber diameter (mm)
φ
2.2
φ
1.0
■Direct connection of ber (Fiber diameter: φ 2.2)
Push the knob of the ampli er's ber connection port downward,
and insert the ber into the ber connection port until it touches the
end, and then raise the knob to the original position.
Knob
■Connection of ber via attachment (Fiber diameter: φ 1.0)
Push the knob of the ampli er's ber connection port downward,
and insert the ber into the ber connection port until it touches the
end, and then raise the knob to the original position.
Attachment for ne ber (E39-F9), manufactured by OMRON
E39-F9 shall be separately purchased.
■Cutting a ber
To cut a ber, use the ber cutter included in the ber unit.
Insert the ber through a hole of the ber cutter that ts the ber
diameter, and cut the ber at a right angle.
Do not use a hole that has been used once.
*
The ber cutter (B289-FC) is included in the AnyWireASLINK ber unit
(AFT-4, AFT-1, AFT-2 and AFT-1-1) (one piece each).
！
CAUTION
-L*F1011 6/11-
Connecting method
Direct connection
Connection via attachment (E39-F9)
Fiber connection port
With the tip of the ber protruding
from the tip of the attachment by
0.5mm
approx. 0.5mm, connect the ber
to the ampli er.
Fiber cutter
*
B289-FC
To reuse a ber that has already been connected, cut
the tip of of the ber.
Failure to observe this instruction causes reduction in
light emitting/receiving quantity.