3onedata IGW1111 Series Руководство по быстрой установке - Страница 3
Просмотреть онлайн или скачать pdf Руководство по быстрой установке для Шлюз 3onedata IGW1111 Series. 3onedata IGW1111 Series 4 страницы. Industrial modbus gateway
Также для 3onedata IGW1111 Series: Руководство по быстрой установке (4 страниц)
Печатать страницу
P
rovide 3IN1 serial port, which supports
RS-232, RS-485 or RS-422 (optional). The
interface type is DB9 male and its pin
definitions are as follows:
PIN
RS-232
RS-422
1
DCD
T-
2
RXD
T+
3
TXD
R+
4
DTR
R-
5
GND
GND
6
DSR
—
7
RTS
—
8
CTS
—
9
—
—
【Checking LED Indicator】
The LED indicators on the front panel of this series device
monitor the device working status, which has simplified the
overall troubleshooting process. The function of each LED is
described in the table as below:
LED
Indicate
Description
PWR is connected and running
ON
normally
P1-P2
PWR is disconnected or running
OFF
abnormally
The system is running normally
Blinking
The system is not running or
OFF
RUN
running abnormally
The system is running
ON
abnormally
LAN port has established valid
ON
network connection
LAN port is in an active network
LINK (1-2)
Blinking
status
LAN port hasn't established valid
OFF
network connection
LED
TX (1-4)
RS-485
—
RX (1-4)
—
D+
【Logging in to WEB Interface】
D-
Support WEB management and configuration. Computer can
GND
access the device LAN1 via Ethernet interface. The way of
—
logging in to device's configuration interface via IE browser is
—
shown as below:
—
Step 1
Configure the IP addresses of computer and the
—
device to the same network segment, and the
network between them can be mutually accessed
Step 2
Enter device's IP address in the address bar of the
computer browser.
Step 3
Enter device's username and password in the login
window as shown below.
Step 4
Click "Login" button to login to the WEB interface of
the device.
Note:
In the Dual IP mode, the default IP address of LAN1 is
Indicate
Description
Serial port is not transmitting
OFF
data or transmitting data
abnormally
Serial port is transmitting data.
Blinking
Serial port is not receiving data
OFF
or receiving data abnormally
Serial port is receiving data.
Blinking
"192.168.1.254", the default IP address of LAN2 is
"192.168.8.254".
The default user name and password of the device are
"admin".
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
10/100Base-T(X)
100M copper port
RJ45 port
RS-232/485/422 3IN1
DB9M interface
serial port
CLI command management port
Console port
(RS-232), RJ45
Power indicator, Running status
indicator,
Indicator
indicator,
transmission/receiving
indicator
Power Supply
12~48VDC, dual power supply
Input power supply
redundancy, support non-polarity
6-pin
or
Access terminal blocks
terminal
occupies 4 pins in the left
Power Consumption
No-load:
1.3W@12VDC (high temperature)
Model I
Full-load:
1.6W@12VDC (high temperature)
Model II
No-load:
self-adapting
Network
Link/Act
Serial
port
state
8-pin
5.08mm
pitch
blocks,
power
supply