Casio 2168 Руководство по эксплуатации

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Смотреть Casio 2168. Casio 2168 2 страницы.

Печатать страницу

MA0905-EC

Operation Guide 668 2168 2505

About This Manual

General Guide

• • • • • Press B to change from mode to mode.

• • • • • Pressing B after performing some operations in any mode returns to the

Timekeeping Mode.

• • • • • If you do not perform any operation for a few minutes in the Alarm Mode or

Setting Screen, the watch automatically reverts to the Timekeeping Mode.

Timekeeping Mode

Minutes

Hour

Seconds

Day

Day of week

Charge indicator

PM indicator

Flashing

3. While the seconds setting is selected (flashing), press C to reset it to 00. If you

press C while the seconds setting is in the range of 30 to 59, the seconds are

reset to 00 and 1 is added to the minutes. If the seconds setting is in the range

of 00 to 29, the minutes count is unchanged.

4. While any other setting is selected (flashing), press C to increase the number.

• • • • • Holding down C changes the setting at high speed.

5. After you set the time and date, press B to return to the Timekeeping Mode.

Alarm Mode

Minutes

Hour

Mode indicator

Hourly time signal on indicator

Alarm on indicator

2. Press A to change the selection in the following sequence.

Daily Alarm and

Hourly Time Signal

on and off

3. Press C to increase the selected digits. Holding down C changes the number

at high speed.

• • • • • The format (12-hour and 24-hour) of the alarm time matches the format you

select for normal timekeeping.

• • • • • When setting the alarm time using the 12-hour format, take care to set the time

correctly as morning or afternoon.

To stop the alarm

• • • • • Press A to stop the alarm after it starts to sound.

• Button operations are indicated using the letters

shown in the illustration.

Alarm Mode

Press B.

In the Timekeeping Mode, press C to switch between

the 12-hour and 24-hour formats.

• • • • • When the 12-hour format is selected, the indicator PM

appears on the display to indicate "P.M." times. There

is no indicator for "A.M." times.

• • • • • When the 24-hour format is selected, the indicator

24H appears on the display.

• • • • • A charge indicator appears on the display of this

watch when charging is required.

To set the time and date

1. Press B three times in the Timekeeping Mode to

display the setting screen.

2. Press A to move the selection (flashing) in the

following sequence.

Seconds

Hour

Day

Day of week

When the Daily Alarm is turned on, the alarm sounds for

20 seconds at the preset time each day. When the

Hourly Time Signal is turned on, the watch beeps every

hour on the hour.

To set the alarm time

1. Press A while in the Alarm Mode. The hour digits

flash because they are selected .

• • • • • At this time the alarm is automatically turned on.

Hour

Minutes

Stopwatch Mode

To turn the Daily Alarm and Hourly Time Signal on and off

Press C while in the Alarm Mode to change the status of the Daily Alarm and

Hourly Time Signal in the sequence shown below.

Both ON

• • • • • The alarm and hourly time signal indicator is displayed in all modes.

To test the alarm

Hold down C while in the Alarm Mode to sound the alarm.

Stopwatch Mode

1/100 second

Seconds

Minutes

Month

Mode indicator

Elapsed time measurement

Start

Split time measurement

Start

Split time and 1st-2nd place times

Start

Power Requirements

This watch works by light energy, so no battery is necessary. Light energy is

converted into electric energy by solar cells and stored into the capacitor. Once

fully charged, the watch can continue to run for a number of days (Modules 668

and 2168: 4 days, Module 2505: 14 days) without being exposed to light.

I Charging light

• • • • • The watch will start to work within about two seconds after it is exposed to light

(such as general office illumination). Set the time and calendar at this time.

• • • • • You can put on the watch after the "charge indicator (

display.

• • • • • The beeper sound may be weak and the display may be dim while the charge

indicator is on the display.

• • • • • Use the information in the table below as a reference how long you need to

expose the watch to light when charging it.

Setting Screen

Both OFF

Daily Alarm

Only

The Stopwatch Mode lets you measure elapsed time,

split times, and two finishes. The range of the

stopwatch is 59 minutes, 59.99 seconds.

Stop

Re-start

Stop

Split

Split release

Stop

Split

Stop

Split release

First runner

Second runner

Display time of

finishes.

second runner.

Display time of

first runner.

)" disappears from the

Hourly Time

Signal Only

Clear