Daniela DANDW45BS Руководство пользователя - Страница 12
Просмотреть онлайн или скачать pdf Руководство пользователя для Посудомоечная машина Daniela DANDW45BS. Daniela DANDW45BS 18 страниц. 45cm stainless steel electronic dishwasher
Печатать страницу
HOW TO CONNECT THE SAFETY SUPPLY HOSE
The appliance must be connected to the water mains using new hose-sets. The old hose-sets
should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa.
f the pressure is below the minimum consult our Service Department.
1.
Pull The safety supply hoses completely out from storage
compartment located at rear of dishwasher.
2.
Tighter the screws of the safety supply hose to the faucet
with thread 3/4inch. for advice.
3.
Turn water fully on before starting the dishwasher.
ABOUT THE SAFETY SUPPLY HOSE
The safety supply hose consists of the double walls. The hose's system guarantees its
intervention by blocking the flow of water in case of the supply hose breaking and when the air
space between the supply hose itself and the outer corrugated hose is full of water.
WARNING!
A hose that attaches to a sink spray can burst if it is installed on the same water line as the
dishwasher. If your sink has one, it is recommended that the hose be disconnected and the
hole plugged.
HOW TO DISCONNECT THE SAFETY SUPPLY HOSE
1.
Turn off the water.
2.
Release the water pressure by depressing the pressure release button. This relieves water
pressure and protects you, and the room, from severe splashing.
3.
Unscrew the safety supply hose from the faucet.
COLD WATER CONNECTION
Connect the cold water supply hose to a threaded 3/4 inch connector and make sure that it
is fastened tightly in place. If the water pipes are new or have not been used for an extended
period of time, let the water run to make sure that the water is clear and free of impurities.
If this precaution is not taken, there is a risk that the water inlet can get blocked and damage
the appliance.
PA G E 2 2
P
I
02 9604 1226
E
I
How to Connect the safety supply hose
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the
minimum consult our Service Department for advice.
1
Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.
2
Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.
3
Turn water fully on before starting the dishwasher.
ABOUT THE SAFETY SUPPLY HOSE.
The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking the
flow of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer
corrugated hose is full of water.
WARNING!
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink
has one, it is recommended that the hose be disconnected and the hole plugged.
How to Disconnect the safety supply hose
1
Turn off the water.
2
Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
room, from severe splashing.
3
Unscrew the safety supply hose from the faucet.
COLD WATER CONNECTION
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked
and damage the appliance.
Drain hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
W
|
danielaappliances.com.au
flow of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer
corrugated hose is full of water.
WARNING!
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink
has one, it is recommended that the hose be disconnected and the hole plugged.
How to Disconnect the safety supply hose
1
Turn off the water.
2
Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
room, from severe splashing.
3
Unscrew the safety supply hose from the faucet.
COLD WATER CONNECTION
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked
DRAIN HOSE CONNECTION
and damage the appliance.
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the
Drain hose Connection
sink, making sure to avoid bending or crimping it. The top of the hose must be less than 1000mm.
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
Front
NOTE
The top of the hose
must be less than
1000mm.
Drain pipe
HOW TO DRAIN EXCESS WATER FROM HOSES
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly into
the sink. It will be necessary to drain excess water from hoses into a bowl or suitable container
that is held outside and lower than the sink.
WATER OUTLET
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water drain hose is not kinked or squashed.
EXTENSION HOSE
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be
reduced. Ensure that the water drain hose is not kinked or squashed.
SYPHON CONNECTION
The waste connection must be at a height less than 1000 mm (maximum) from the bottom of the
dish. The water drain hose should be fixed.
P
I
02 9604 1226
E
I
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
Counter
A
B
40mm
14
14
W
|
danielaappliances.com.au
PA G E 2 3