DANLERS EZ CESR Указания по установке - Страница 2

Просмотреть онлайн или скачать pdf Указания по установке для Переключатель DANLERS EZ CESR. DANLERS EZ CESR 2 страницы. Easyzapp ceiling flush mounted switches

Печатать страницу

Installation procedure

1. Please read these notes carefully before commencing work. In case of doubt

please consult a qualified electrician. Ensure wires and cables are securely held

within the connection terminals.

IMPORTANT: The EZ CESR Control Unit clock battery must be engaged (ON)

prior to installation by switching the RED dip switch (see diagram E) to the

DOWN position.

2. POSITIONING: The EZ CESR switch should be installed to achieve correct

coverage of the area, see diagram B. If the photocell override facility (enabled

via EasyZAPP app) is required, the switch must be located above an area where

daylight can give greater illumination than the artificial light. Avoid locating this

product where it is exposed to drafty conditions (exposed lobbies, open ceiling

voids or near fans) or near heat sources. To cover large areas PIRs should be

spaced in a 5 metre grid formation.

3. Disconnect the PIR from the circuit before performing insulation testing of the

wiring circuit.

4. Do not connect on a circuit with large inductive loads, as induced spikes may

cause false triggering or damage the PIR.

5. EZ CESR must be connected to the EasyZAPP Power Supply (CZPS) via the

EasyZAPP communication cable (telejack) provided, for wiring see diagrams C and

NOTE: The use of non EasyZAPP connectors may damage the EZ CESR or CZPS

and will invalidate the warranty).

6. Knockout or drill the appropriate holes on the mounting plate for attaching the plate

to the ceiling or back box (if applicable). Feed telejack through the appropriate (side

or rear) entry hole. Screw the back mounting plate to the ceiling or back box via the

mounting holes. Push the telejacj connector into the sensor head terminal. Push the

sensor head onto the mounting plate and align the side clips with the slots on the

sensor heads.

Settings and calibration

ALL settings are adjusted by EasyZAPP App as detailed in the free to download

EasyZAPP App User Guide, including:

Timeout: Adjustable time lag from 10 seconds to 24 hours.

Brightness: Adjustable switching threshold, 30 to 1000 lux and inactive. EZ CESR

must be calibrated as instructed on the user guide manual.

Batch Configure: For configuring multiple EZ CESR controls with identical settings.

Name: For identifying individual controls.

Password: For security against accidental or malicious alteration.

Please visit www.danlers.co.uk to download the EasyZAPP user guide.

A: Mounting diagram

Knock out mounting

For telejack entry from

holes or pre-drill

above - knock out

pilot holes.

central mounting hole

B: Detection diagram

Strong detection zone

i.e. person moving arm

or walking towards PIR

up to 5m

up to 7m

C: Wiring diagram

Single EZ CESR

100 - 260 VAC

50 / 60 Hz

load

D: Connector diagram

Several EZ CESR wired in parallel

IMPORTANT

Red dip switch (MUST be

100-260 VAC

switched towards centre of control)

50 / 60 Hz

to engage clock battery ON

Power Supply

Telejack connector

Clip telejack into the device

For side entry -

then join device to mounting

knock out side

plate via mounting clips

mounting hole

For optimum coverage

recommended

mounting height: 2.4 to 5m

Single EZ CESR

Secondary detection

zone i.e. person

walking perpendicular

to PIR

100 - 260 VAC

50 / 60 Hz

D: Wiring diagram

Several EZ CESR wired in parallel

100-260 VAC

50 / 60 Hz

Control Unit

load