Audiopipe APMA-2100 Руководство пользователя

Просмотреть онлайн или скачать pdf Руководство пользователя для Усилитель Audiopipe APMA-2100. Audiopipe APMA-2100 4 страницы. Mini design 2 channel class d amplifier

Печатать страницу

Caution:

Continuous exposure to sound pressure levels in excess 011 DDdB сап cause permanent hearing

loss. This unit is сараЫе 01 producing sound pressure levels well over 17DdB. Please observe all

local sound ordinances while listening to your system.

Features:

- Douыe Side РСВ And SMD Components

- Full Range Digital or Class D Design

- LPF and HPF (Subsonic) Crossovers

§pecifications:

• 2 х 100W RMS@ 14.4V

- FRD Chlp Technology

- Up to 2n staЫe

- Auto ТUrn Оn/ОИ

- Up to 3DDHz Low Pass

- Up to &DHz Subsonlc (НР)

- Up to 4V Low Level lnput

• Up to 15V Hlgh Level lnput

- Frequencv Response: 2DHz~2DКНz

• THD: <0.3о/о @4n load

Control Functions:

1. Speakers:

Connect speakers/subwoolers to these terminals. Ве sure to check wire lor proper polaritv. Never

connect the speaker саыеs to chassis ground.

2. + 12V Power:

Connect this terminal through а FUSE or CIRCUIT BREAKER to the positive terminal 01 the vehicle

ьanerv or the positive terminal 01 an isolated audio system ьanerv.

Warning: Always protect this power саые ьv installing а luse or circuit breaker 01 the appropriate

size within 15" (38cm) ol the ьanerv terminal connection.

3. Remote turn on:

This terminal turns on the amplilier when

lead 01 the head unit or signal source.

4.GND:

Connect this саые directlv to the lrame 01 the vehicle. Make sure the metal lrame has been stripped

01 all paint down to the ьаrе metal. Use the shortest distance possiЫe. 11 is always а good idea to

replace the lactorv ground at this time with а larger саые equal to the new amplilier power саые or

larger. CAUTION: Do not connect this terminal directly to the vehicle ьanerv ground terminal or any

other lactory ground points.

5. RCA input jacks:

RCA input jacks are lor use with source units that have RCA outputs. А source unit with а minimum

level ol 2DDmV is required lor proper operation. The use ol high qualilY twisted pair саЫеs is

recommended to decrease the possibililY ol radiated noise entering the svstem.

&. lnput Mode Switch:

This switch elects the input mode. When using the high level input the amplilier will turn on on

when signal is sensed ьv the internal circuit. There is no extra Remote signal demanded at High

Level lnput Mode.

Miпi Desigп i!! Сhаппеl

Class D Aпlplit=ier

- SwitchaЫe low or high lnput Mode

- Auto turn on/on @ High lnput Mode

• S/N Ratio:

- Eniciencv:

- Fuse Protection: 2DA

- Thermal protect:@ B 4

- Street Series Plug Prewired

- Up to BGa Power Terminal

- Dual Side solid РСВ with SMD

- Heavy dutv stackaЫe heatsink

- Dimensions: 5.5" х 3.7" х 1.7" (140 х 94 х 44mm)

12V is applied to it. Connect it to the remote turn on

User"s Manual

APМA-i!IOO

90dB

7Do/o @ 4n

C/185