AudioSource AMP 102 Руководство пользователя - Страница 4
Просмотреть онлайн или скачать pdf Руководство пользователя для Усилитель AudioSource AMP 102. AudioSource AMP 102 17 страниц. Home audio multi-zone power amplifier
Также для AudioSource AMP 102: Руководство по применению (12 страниц), Руководство пользователя (1 страниц)
Печатать страницу
AMP102 / AMP110
OWNER'S MANUAL
Speakers
A
B
2
FRONT PANEL CONTROLS
1. Power
The front panel power switch switches the AMP102/110 on or off. Red
LEDs behind the faceplate indicate power status. Whenever the amplifier's
power switch is in the "ON" position the ring around the button is illuminated.
When the amp is "Active" (receiving signal) the side lenses become
illuminated and the signal LEDs show green. During "Standby" status (no
signal) the side lenses are not illuminated and the signal LEDs show orange.
2. Speaker Selector
Selects speaker set ( A or B )
Line 1
IN
L
R
Serial Number:
6
REAR PANEL CONTROLS
6. Line 1 Input
A switching input that can be used if a second source is desired and will
take over when a signal is present and has at least a 5mV level. Whenever
there is no signal at this input, or a signal with less than 5mV level, the
amplifier switches back to the Line 2 or "primary" input.
7.
Line 2 Input/Output
The primary line level input and output for a single source connection.
8.
Mode Select Switch
Switches the amplifier from Stereo mode to Bridged mode.
9.
12V Trigger
Allows the AMP102/110 to be powered on by other electronics or to power
on other electronics via a 3.5mm mini phone plug cable.
10.
Power Mode
Sets the power on option of the AMP102/110. Set it to Normal for manual
power on/off. Set to Auto-On for signal sensing. Set to Trigger if the 12V
Trigger input is used.
11.
Light Bar Display Control
Turns light bar display on front panel on or off. Does not control Signal/Clip
LEDs or power button light ring.
12.
Right Channel Speaker Output
Right channel terminals for speaker outputs A and B.
4
Connect
Receiver
Here
CAUTION
RISK OF FIRE OR ELECTRIC SHOCK
DO NOT OPEN
CAUTION
: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE
COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
Line 2
Line 2
WARNING
: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE
IN
OUT
COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
Mode
12V Trigger
+
-
Stereo Bridged
IN
7
9
8
13970 SW 72nd Ave. Portland, OR 97223 • 503.914.4688 • www.audiosource.net
AMP102
Stereo Power Amplifier
Power
Signal / Clip
Signal / Clip
Left
Right
5
1
5
3. Balance
Fades speaker output between the Right and Left Channels
4. Volume
Adjusts amplifier volume.
5. Clip LEDs
Blinks red during signal clipping. Reduce volume slightly.
Shows solid green (AMP102) or orange (AMP110) during protect mode.
Check speaker wires for shorts or extreme low impedance (< 4 ohms).
AVIS
Minimum Impedance:
AVIS: RISQUE DE CHOC ELECTRIQE
NE PAS OUVRIR CE CARTER
8 ohm Bridged
RESERVE AU PERSONNEL AUTORISE
4 ohm Stereo
Light Bar Display
On Off
Auto On
OUT
Trigger Normal
10
11
13.
Left Channel Speaker Output
Left channel terminals for speaker outputs A and B.
14.
Mains Power Inlet & Fuse Holder
Accepts IEC type line cord. A fuse in the integrated holder provides safety
protection from fault conditions: replace fuse with one of same type
and rating only.
15.
Mains Voltage Selector
Voltage selection switch is preset to 115V (USA). For use in areas which
require 230V contact your dealer. Fuse must be of type and rating marked
on amplifier for use at local mains voltage.
Balance
Left
Right
3
Speaker A
MODEL AMP102
-
R
+
+
L
-
Custom Manufactured in China
115V~ 60Hz 500W
FUSE:T4AL 250V
230V~ 50Hz 500W
FUSE:T2AL 250V
Bridge
-
+
L
-
-
R
+
+
Speaker B
CAUTION: See User Manual Before
12
13
14
Volume
Min
Max
4
Figure 1. Front Panel
15
Replacing Fuse
Figure 2. Rear Panel