AudioSource AMP102VS Руководство пользователя - Страница 3
Просмотреть онлайн или скачать pdf Руководство пользователя для Усилитель AudioSource AMP102VS. AudioSource AMP102VS 4 страницы.
Печатать страницу
1
2
FRONT PANEL CONTROLS
1. Power Switch
Switches the AMP102VS on or off.
2. Speaker Selector
Selects speaker zone A or B. For A + B zones push both buttons in.
CAUTION
RISK OF FIRE OR ELECTRIC SHOCK
DO NOT OPEN
L
R
Serial Number:
REAR PANEL CONTROLS
6. Bass and Treble Controls
These controls can adjust bass and treble frequencies +/- 12dB at 100Hz
and 10kHz.
7. Interupting Line Input
This is the secondary input, use MAIN IN for your main input.
INTERRUPTING INPUT can be used if a second source is desired and
takes over when signal is present and has at least a 5mV level.
When there is no signal, or a signal with less than 5mV level, the amp
switches back to MAIN IN after a brief delay.
8.
Main Input/Output
MAIN IN should be used as the "primary" or main input for the amplifier.
Connect your receiver or main source to this input. Use MAIN OUT to pass
MAIN IN signal to another amplifier.
9.
Mode Select Switch
Switches the amplifier from Stereo mode to Bridged mode.
STEREO MODE
If you will be connecting one or two pair of speakers to the amplifier, place
the switch in the "Stereo" position. NOTE: For playing 2 pairs of speakers
(A plus B), make sure each speaker has an impedance of 8 ohms or greater.
BRIDGED MODE
When set to "Bridged" mode, the amplifier is a single channel mono amplifier.
BRIDGED MODE- MONO APPLICATION
For bridged mode, playing Right and Left together as mono output, use a
Y cable adapter to connect Right and Left RCA signal to the Right (Red) input
at MAIN IN. Set the MODE switch to BRIDGED and follow the instructions
for bridged speaker connection in the SPEAKER TERMINALS section of
this manual.
NOTE: The AMP102VS supplies 160W in bridged mode, Please verify that your
speakers are capable of handling such power to avoid possible damage!
10. 12V Trigger
Allows the AMP102VS to be powered on by other electronics or to power
on other electronics via a 3.5mm mini phone plug cable.
11.
Power Mode Select Switch
Sets the power on option of the AMP102VS. Set it to Normal for manual
power on/off. Set to Auto-On for signal sensing. Set to Trigger if the 12V
Trigger input is used.
13970 SW 72nd Ave, Portland, OR 97223 • 503.914.4688 • www.audiosource.net
AVIS
AVIS: RISQUE DE CHOC ELECTRIQE
NE PAS OUVRIR CE CARTER
RESERVE AU PERSONNEL AUTORISE
Interrupt
Main In
IN
IN
OUT
Mode
Stereo Bridged
7
8
9
3. Balance
Fades speaker output between the Right and Left Channels
4. Volume
Adjusts amplifier volume.
6
Minimum Impedance:
8 ohm Bridged
4 ohm Stereo
12V Trigger
Auto On
+
-
IN
OUT
Trigger Normal
10
11
12.
Speaker Zone A Output
Speaker output terminals for zone A. Minimum impedance: 8 ohm bridged
or 4 ohm stereo.
13.
Speaker Zone B Output
Speaker output terminals for zone B. Minimum impedance: 8 ohm bridged
or 4 ohm stereo.
SPEAKER TERMINALS - STEREO MODE
For stereo output connect the speaker's positive (red) terminal to the amplifier's
positive (red) terminal, and the speaker's negative (black) terminal to the
amplifier's negative (black) terminal for each Right and Left speaker.
SPEAKER TERMINALS - BRIDGED MODE
Place the "MODE" switch in the "BRIDGED" position and use both red
terminals to connect to the speaker. Connect the speaker's positive (red)
terminal to the amplifier's red (+) terminal noted next to the bridging mark, and
the speaker's negative (black) terminal to the amplifier's unmarked positive
(red) terminal.
NOTE: Only one zone (A or B) can be bridged. Do not attempt to bridge both
A and B speaker terminals! This may result in a lower impedance than the
amplifier is designed for and may damage your amplifier. The minimum
impedance for the total load connected in bridged mode is 8 ohms.
NOTE: Use Class 2 wiring for speaker connections.
To wire the output connector: 1. Strip the insulation off each speaker wire
to expose 3/8" (10 mm) of bare conductor. 2. Unscrew the output terminal
binding post several twists, insert each wire into the correct terminal.
3. Tighten binding post by twisting clock-wise until it is firmly clamping the
speaker wire.
Warning: While the amplifier does self-protect under most improper output
conditions, misconfiguration of loudspeaker mode and incorrect connection
of loudspeakers could damage connected loudspeakers and/or amplifier.
Please refer installation to a qualified installation professional, and always
check state and local electrical codes when installing.
AMP102VS
OWNER'S MANUAL
3
12
Speaker A
MODEL AMP102VS
-
R
+
+
L
-
Custom Manufactured in China
115V~ 60Hz 500W
FUSE:T4AL 250V
230V~ 50Hz 500W
FUSE:T2AL 250V
+
Bridge
-
-
+
+
L
-
R
Speaker B
CAUTION: See User Manual Before
13
Replacing Fuse
4
Figure 1. Front Panel
15
14
Figure 2. Rear Panel
3