Audiotec Fischer UP 10DSP Инструкции по установке
Просмотреть онлайн или скачать pdf Инструкции по установке для Автомобильная стереосистема Audiotec Fischer UP 10DSP. Audiotec Fischer UP 10DSP 2 страницы. Extension card
Печатать страницу
EXTENSION CARD
HEC / MEC BT HD
High Definition Bluetooth
®
Congratulations!
Dear Customer,
congratulations on your purchase of this high-qual ity HELIX / MATCH
EXTENSION CARD. We developed the BT HD based on state-of-
the-art engineering and this is reflected in its exceptional quality and
the impressive use of sophisticated technologies.
We hope you enjoy using this product.
Yours,
AUDIOTEC FISCHER
General installation instructions for HELIX / MATCH components
To prevent damage to the unit / module and possible injury, read this
manual carefully and follow all installation instructions. This product
has been checked for proper function prior to shipping and is guaran-
teed against manufacturing defects.
Before starting your installation, disconnect the battery's nega-
tive terminal and all cables from the device to prevent damage
to the unit / module, fire and / or risk of injury. For a proper perfor-
mance and to ensure full warranty coverage, we strongly recommend
to get this product installed by an authorized HELIX / MATCH dealer.
Install the Extension Card only in the designated device and its
specific slot. Using the module in other devices or slots can re-
sult in damage of the Extension Card, the device, the head unit /
radio or other connected devices!
Technical data
Bluetooth
standard:
®
Bluetooth
profile:
®
Bluetooth
codec:
®
Number of paired devices:
Wireless frequency range:
Range:
Digital optical output:
Status LED of BT HD
Blue
LED on: 1 sec,
off: 2 secs, repeat
Blue
&
Red
LED flash alternate
Blue
LED flash every 2 sec.
Blue
LED flash twice every 2 sec. Device is streaming
Hünegräben 26 · 57392 Schmallenberg · Germany · Tel.: +49 2972 97880 · E-mail: [email protected]
5.0 Audio Streaming Module
5.0 + EDR
A2DP, AVRCP, SPP
SBC, AAC, Qualcomm
®
and Qualcomm
aptX
HD
®
™
8
2402 ~ 2480 MHz
Up to 10 m
SPDIF with either 96 kHz / 24 Bit
or 48 kHz / 24 Bit depending on
sampling rate of the device
All profiles are in standby
but not connected with any
Bluetooth
device yet
®
Enter pairing mode
Device is connected
Mounting information
1. First disconnect all cables from the device.
2. Depending on the device there are two possibilities to get access
to the Extension Card slot.
1. Bottom plate is bolted: untighten the screws of the bottom plate
and remove it. Afterwards dismantle the appropriate side panel by
removing its screws.
2. Bottom plate is not bolted: dismantle the appropriate side panel
by removing its screws and pull out the bottom plate sideways.
3. Remove the nut and the washer from the antenna socket of the
Extension Card.
4. Insert the Extension Card into the specific slot of the device which
is marked in the following picture (the picture representatively dis-
plays the Extension Card slot of the HELIX DSP.3). The exact
position of the slot can be found in the manual of each device.
5. Make sure that the module is installed properly and all pins are
fully inserted into the socket:
6. If the bottom plate was bolted, fix the new side panel which is
aptX
™
delivered with the Extension Card. Afterwards reinsert the bottom
plate and fix it, too. Otherwise reinsert the bottom plate and fix the
new side panel with the screws.
7. Put the washer and the nut on the antenna socket and bolt it to
the side panel.
Caution: Do not overtighten the nut as this may damage the
socket!
8. Reconnect all cables to the device.