Audiotec Fischer HELIX DSP.2 Инструкции по установке - Страница 2
Просмотреть онлайн или скачать pdf Инструкции по установке для Сигнальные процессоры Audiotec Fischer HELIX DSP.2. Audiotec Fischer HELIX DSP.2 2 страницы. Extension card
Печатать страницу
EXTENSION CARD
HEC / MEC BT HD
Signal routing of the Extension Card
As soon as the Extension Card is installed, it is automatically detect-
ed by the device. Now you can allocate the Extension Card to the
desired outputs in the "HEC (MEC) / AUX Routing" matrix.
Several new features are visible in the DSP PC-Tool after installing
an Extension Card.
Pairing of the Extension Card with other Bluetooth
The HEC / MEC BT HD module supports the A2DP profile featur-
ing Qualcomm
aptX
, Qualcomm
®
™
maximum sound performance. The digital Bluetooth
I²S format is directly fed into the DSP without any additional signal
conversion. A one-time pairing procedure is mandatory to establish
a connection between the HELIX / MATCH device and your device
with Bluetooth
wireless technology. Make sure that the Bluetooth
®
function on your device has been activated before you start the pair-
ing process.
Important: The Status LED of the HEC / MEC BT HD module flash-
es alternately blue and red. After three minutes the pairing mode is
left automatically if the connection has not been established.
Option a)
Turn on the HELIX / MATCH device and push the "control" button for
less than 1 sec. in order to start the pairing mode.
The picture representatively displays the "control" button of the HELIX DSP.3
Option b)
Start the pairing mode in the DSP PC-Tool software:
After the pairing mode is activated the Bluetooth
found under the name "ATF BT HD".
Hünegräben 26 · 57392 Schmallenberg · Germany
Tel.: +49 2972 97880 · E-mail: [email protected]
devices
®
aptX
HD and AAC codec for
®
™
data stream in
®
network can be
®
Option c)
Start the pairing process through the CONDUCTOR or DIRECTOR
remote control.
DIRECTOR:
Go to the Bluetooth
"Pair" button.
CONDUCTOR:
Switch to a Volume Control or Bluetooth Playback
control menu and press the rotary knob for more
than 5 seconds.
WIFI CONTROL: Go to the HEC / MEC menu and push the "Pair"
button under the Bluetooth
Further information will be found in the corresponding user manual.
The HEC / MEC BT HD module can be paired with up to eight
Bluetooth
devices. As soon as you try to pair a ninth device, the first
®
one will be erased automatically from the pairing list.
The optical SPDIF output of the HEC / MEC BT HD module
The installation of the Extension Card adds as well an additional
digital optical SPDIF output to your device. This output allows to
transmit any unprocessed input or DSP-processed output signals to
other devices.
A new matrix "Digital Output Routing" appears in the "Input and Out-
put Configuration" page in which you can make your desired settings.
The digital output delivers an uncoded stereo PCM signal with either
®
96 kHz / 24 Bit or 48 kHz / 24 Bit, depending on the sampling rate of
the designated device.
Wireless DSP tuning – only DSP devices with ACO
The HEC / MEC BT HD also offers a wireless configu-
ration of the DSP via the DSP PC-Tool V5 software and
a PC with Bluetooth
wireless technology for all DSP
®
devices equipped with ACO platform.
Therefore follow the subsequent steps:
1. Pair your HEC / MEC BT HD with your PC as explained on the
left side.
2. Start the DSP PC-Tool software (version 5.0 or higher required).
3. Toggle the connect type button, located at the right side naviga-
tion, to "BT". The software now automatically detects the device.
4. Select the device which should be configured and click the "Con-
nect" button. You can now start your configuration.
Warranty disclaimer
The warranty service is based on the statutory regulations. Defects
and damage caused by overload or improper handling are excluded
from the warranty service. Any return can only take place following
prior consultation, in the original packaging together with a detailed
description of the error and a valid proof of purchase.
Technical modifications and errors excepted! We accept no liability
for damage to the vehicle or device defects caused by the incorrect
operation of the device. This product has been issued a CE marking.
This means that the device is certified for use in vehicles within the
European Union (EU).
Legal notes:
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other
countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the
United States and other countries. The Bluetooth
owned by Bluetooth SIG, Inc. and any use of such marks by Audiotec Fischer GmbH is under license.
Other trademarks and trade names are those of their respective owners.
Connect menu and push the
®
Connect section.
®
word mark and logos are registered trademarks
®