Datacom Systems 1000BT-AT-SX Руководство по быстрой установке

Просмотреть онлайн или скачать pdf Руководство по быстрой установке для Сетевое оборудование Datacom Systems 1000BT-AT-SX. Datacom Systems 1000BT-AT-SX 2 страницы. Full-duplex tap

Печатать страницу

DATACOM

Connecting a 1000BT-AT-SX to the the Network

FIGURE 2 — 1000BT-AT-SX Simple Connectivity Diagram

To connect the 1000BT-AT-SX into the network, refer to FIGURE 2 and

follow these steps:

IMPORTANT: The maximum length of 90 meters must not be exceed-

ed between end-points.

1. Before powering the TAP, connect one of the network device cables

to the 1000BT-AT-SX RJ45 port NETWORK A connector.

2. Before powering the TAP, connect the other network device cable to

the 1000BT-AT-SX RJ45 port NETWORK B connector. Ensure link

has been established between the NETWORK A device and NET-

WORK B device.

3. Connect the Power Supply barrel connector into the POWER port of

the 1000BT-AT-SX and then plug the Power Supply into the external

power source wall receptacle. The POWER LED to the right of the RJ

connectors illuminates indicating power is on.

The Rx-A, Tx-A, Rx-B, and Tx-B LEDs illuminate as data is passed

back and forth between the NETWORK A and NETWORK B device.

4. Connect one tap cable from the 1000BT-AT-SX RJ45 port TAP A

connector into one port of the Network Analysis Tool interface card.

The TAP-A LINK LED illuminates indicating link has been established

between the TAP A connector and Network Analysis Tool interface

card.

5. Connect the other tap cable from the 1000BT-AT-SX RJ45 port TAP

B connector into the other port of the Network Analysis Tool inter-

face card. The TAP-B LINK LED illuminates indicating link has been

established between the TAP B connector and Network Analysis Tool

interface card.

DATACOM

SYSTEMS INC

Access Your Network

CAUTION: Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user's authority to operate the

equipment.

This equipment has been tested and found to meet the radiated and conducted

emission limits for a Class B product of EN 55022 to the EMC Directive

89/336/EEC requirements.

This equipment has been tested and found to meet the immunity levels for

Class 1 tested to level 2 for EN 6100-4-2, tested to level 3 for EN 61000-4-

3, tested to level 2 for EN 61000-4-4, and tested to level 3 for EN 61000-4-

5 to the EN 50082-1 requirements and meets the Class A requirements for EN

61000-3-2 and EN 61000-3-3.

This equipment has completed the Product Safety Review and found to meet the

Low Voltage Directive 72/23/EEC (1993) requirements.

Printed in the United States of America. No part of this publication may be

reproduced, stored in a retrieval system, or transmitted, in any form or by any

means, electronic, mechanical, photocopying, recording, or otherwise, with-

out the prior written permission of Datacom Systems, Inc. To obtain this per-

mission, write to the attention of the Datacom Systems legal department at

9 Adler Drive, East Syracuse, New York 13057-1290, or call 315-463-9541.

This Quick Installation Guide was written to help you get to know your new

10/100/1000BT-AT-SX quickly. We would welcome any comments or sugges-

tions you may have regarding this Quick Installation Guide. Please send your

remarks and recommendations via mail, telephone, facsimile, or Internet E-mail.

Datacom Customer Service personnel are available via telephone, facsimile, and

Internet E-mail. Please leave a voice message and our Customer Service Staff will

return your call as soon as possible.

Mail:

Datacom Systems, Inc.

Customer Service

9 Adler Drive

East Syracuse, NY 13057-1290

Tel:

(315) 463-9541

FAX:

(315) 463-9557

E-mail: [email protected]

You can obtain additional information about

Datacom Systems, Inc. and its products and services from the World Wide Web

at http://www.datacomsystems.com or [email protected].

™

DATACOM

1000BT-AT-SX Full-Duplex Tap

Quick Installation Guide

May 2010

Part Number: 541-0078-A.01

Datacom Systems, Inc. (DSI) warrants that the hardware which it supplies will be free

from significant defects in materials and workmanship for a period of two years from

the date of delivery (Warranty Period), under normal use and conditions. In the event

of any such defect, you can return an item of defective hardware, freight prepaid, to

DSI during the Warranty Period, and DSI will repair or replace the defective equipment

and return it to you, freight prepaid. If DSI determines that the equipment is not defec-

tive, it will return it to you, freight collect. DSI shall have no responsibility for any

deficiency resulting from accidents, misuse, modifications, power disturbances

(including use of a power supply not specified by DSI), or various other forms of dis-

aster, e.g., earthquakes, floods, etc.

The warranties set forth above are exclusive and in lieu of all other warranties.

Datacom Systems, Inc. (DSI) makes no other warranties, expressed or implied, and

DSI expressly disclaims all other warranties, including but not limited to implied war-

ranties of merchantability and fitness for a particular purpose. Moreover, the provisions

set forth above state DSI's entire responsibility and your sole and exclusive remedy

with respect to any breach of warranty or contract.

No liability for consequential damages. Under no circumstances and under no theory

of Liability shall DSI be liable for costs of procurement of substitute products or serv-

ices, lost profits, lost savings, loss of information or data, or any other special, indirect,

consequential or incidental damages, arising in any way out of the sale of, use of, or

inability to use, any DSI product or service, even if DSI has been advised of the possi-

bility of such damages.