Dürr NDT ScanX Discover HC Инструкции по быстрому запуску
Просмотреть онлайн или скачать pdf Инструкции по быстрому запуску для Принтер "все в одном Dürr NDT ScanX Discover HC. Dürr NDT ScanX Discover HC 4 страницы. Mobile computed radiography system
Также для Dürr NDT ScanX Discover HC: Инструкции по быстрому запуску (4 страниц)
Печатать страницу
Thank You and Congratulations on your purchase of the ScanX Discover ® HC or the ScanX Discover ® HR Digital Imaging System, a
rugged portable imaging system manufactured by Air Techniques, Inc. for DÜRR NDT. Each system has been designed and manufactured
using state-of-the-art technology to produce the lightest, most rugged and dependable digital imaging system available for the demanding
conditions encountered in portable radiography applications. The scanners are extremely easy to deploy producing excellent quality digital
images in seconds. This efficiency coupled with repeatable consistent image quality provides results that allow the user to make critical
decisions on the spot eliminating the need to return for retakes.
This document provides abbreviated instructions to setup and operate ScanX. Refer to the Operator's Manual included as a PDF file on the
supplied CD Disk for complete instructions to ensure that your ScanX gives the highest level of service.
Although each ScanX has been designed to minimize exposure of personnel to hazards, users must exercise every precaution to ensure
personnel safety, and be familiar with the warnings and cautions presented below and throughout the Operator's Manual.
Use of Accessory Equipment.
The use of ACCESSORY equipment not complying with the equivalent safety requirements of this equipment may lead to a reduced level
of safety of the resulting system. Use of ACCESSORIES or cables other than those specified or provided by the manufacturer may result in
increased EMISSIONS or decreased IMMUNITY of the EQUIPMENT.
Electrical Safety Notes.
– The main power switch is the main power disconnect device.
– Use only the line cord provided with the unit.
– Use only grounded electrical connections.
– Check the device cables for possible damage before switching on. Damaged cables, plugs and sockets must be replaced before use.
– Do not locate unit where it could be sprayed with water, or in a damp environment.
Do Not Attempt Internal Service.
All repairs above and beyond simple maintenance may only be carried out by DÜRR NDT personnel or by a suitably qualified person approved by
DÜRR NDT. Contact your local authorized dealer for service. Failure to heed this directive may result in equipment damage and voiding the warranty.
Warnings and symbols
The warnings and symbols in this document are intended to draw attention to possible injury to persons or damage to machinery.
The following warning symbols are used.
Warning - laser beam.
Voltage hazard that can be a caution
or warning depending on the magni-
tude of the risk.
Danger level
The signal word differentiates between four levels of danger:
DANGER:
Indicates immediate danger of severe injury or death.
WARNING:
Indicates possible danger of severe injury or death.
CAUTION:
Indicates risk of minor injuries.
Indicates information is considered important, The safety alert symbol shall not be used with this
NOTICE:
signal word. When a signal word is used for messages relating to property damage, NOTICE is
the choice of signal word.
Laser Class Warning.
The ScanX is a Class 1 Laser Product [Class 1 Laser Product (IEC 60825)]
The warning label shown on the right identifies the ScanX as a Class I Laser Product (IEC)]. It also alerts the
user to Class 3B Laser potential danger to humans in the event the product is opened during service. There is
no laser radiation from this product when operated and maintained as instructed.
Q u i c k S t a r t I n s t r u c t i o n s
General warning symbol is a
symbol that indicates a hazard. It is
composed of an equilateral triangle
surrounding an exclamation mark.
The safety alert symbol shall not be
used to alert persons of property
damage only accidents.
Page 1 of 4
W i t h B u i l t - I n B a t t e r y
SIGNAL WORD
Description of the type and
source of danger.
Here you will find the possible
results of ignoring the warning.
Follow these measures to
i
avoid the danger.
CAUTION
CLASS 1 LASER PRODUCT
CLASS 3B LASER
RADIATION WHEN OPEN
AVOID EXPOSURE TO BEAM
DANGER
LASER RADIATION WHEN OPEN
AVOID DIRECT
EXPOSURE TO BEAM
COVER REMOVED MAKES
THIS DEVICE A
CLASS IIIb LASER PRODUCT