Elsner WS1000 Color Первые шаги - Страница 2

Просмотреть онлайн или скачать pdf Первые шаги для Системы управления Elsner WS1000 Color. Elsner WS1000 Color 2 страницы. Connect control system
Также для Elsner WS1000 Color: Информация о сборке (2 страниц), Руководство (2 страниц)

Печатать страницу

Selecti-

Presence simulation

You can call up to 16 events with the presence simulation simultaneously or con-

secutively, to give the appearance that people are in the building. A settable delay

for the start time makes the simulation more realistic.

 System > Installation > Presence simulation

Set the Name and display in the Manual menus.

Configuration:

Select an event from the list and apply it. The start can be defined as follows:

•

Time: Event starts at specific time

•

Time and brightness: Event starts if a set brightness is undercut in a defined

period.

•

Event X: Event starts as soon as Event X has started

With a random delay, a range can be set, by which the start time of an event is de-

layed.

The motor or the device / light is selected with the "Select function" button.

Initial setting steps

Network connection (internet)

The Control System WS1000 Connect is internet-ready and can be connected

to a network by cable (Ethernet/LAN) or WiFi (WLAN). The network connection is

needed for:

•

Use of Apps (with smartphones and tablets in the same network/WLAN)

If the WS1000 Connect is also connected to the internet via the internal network,

the following functions are also possible:

•

Accessing web contents in the controls' browser

•

Remote access (e.g. for system set-up, diagnosis)

The Ethernet/LAN connection terminal can be accessed after removing the display,

without having to remove the touch protection (cover for 230 V power area). Note

the information regarding assembly.

Set up network connection

 System > Set up WS1000 > Internet

Connection status:

Shows the current status (disconnected or connected).

Connection type:

Shows the type of connection (Ethernet or WLAN). Touch the field to set up the

connection.

WLAN: Wireless connection. If WLAN has been confirmed, the additional field

"Network name" is displayed for the additional set up.

Ethernet: Cable connection via the LAN socket on the circuit board. No other set-

tings necessary.

Network name (SSID):

The network is selected and set up here under the setting WLAN. Enter a network

name or touch "Find networks" to view all available networks.

Create connection:

You can only "Create connection" using this touch field once a network has been

selected. The password for the network is requested.

If necessary, use the same field to terminate the connection.

Protect your network with the latest encryption technology

and change your passwords regularly!

Remote set up/remote maintenance

Access to the Control System WS1000 Connect is possible via the internet

using the remote maintenance function. There must be an internet connection for

this (see chapter Network connection (internet)). A service technician can then see

and change the settings without being on site.

Access to the controls is only possible if remote maintenance is also started on the

device. This is not a remote control option! If you want to operate the controls and

your building technology on the go, then use the WS1000 Connect App and set up

a secure VPN connection for your home network.

 System > Set up WS1000 > Service

Start remote maintenance software:

The software opens. Follow the instructions. To create the connection, the device

ID of the WS1000 Connect must be input at the PC used for the remote mainte-

nance. Then every menu and function of the WS1000 Connect can be viewed

and controlled from the PC.

Status

Close remote maintenance software:

informa-

Ends the active remote maintenance session.

Using an SD card

Control

buttons

The Control System WS1000 Connect can load data from a

micro SD card. The SD card storage is needed for:

•

Screen saver data

•

Update files for software updates

•

Saving settings (configuration file)

The card socket is located on the right-hand side of the device.

The SD card is pushed into the slot, until it clicks into place.

To remove, briefly press the card into the socket so that is jumps

out.

Updates

The software for the Control System WS1000 Connect can be updated during

normal operation. If the control is connected to the internet, the control downloads

updates automatically after confirmation. Alternatively, you load the new software

from the Elsner Elektronik website and save it to the SD card. After inserting the SD

card into the socket on the WS1000 Connect, continue.

 System > Set up WS1000 > Device information

Check for updates:

Shows the currently installed version and facilitates the installation of SD card or

the search for updates on the internet. Follow the download and installation inst-

ructions on the display.

Screen saver (slide show)

The WS1000 Connect can display picture file, time/temperature as a screen saver

or simple a black screen. The screen saver is activated if the display has not been

touched for 5 minutes. To start the screen saver manually, stay longer on the circle

in the lower navigation bar.

Additionally, the display brightness can be adjusted automatically to the room

brightness and the screen can switch off when dark.

 System > Set up WS1000 > Settings

Display:

Shows which screen saver is currently active and whether automatic brightness is

switched on.

Select the screen saver:

•

Without

•

Black screen

•

Time/temperature display

•

Picture display (slide show or single picture)

In order to show digital picture data as a slide show, save the files to a micro SD

card. The picture files must meet the following requirements:

•

The files must be saved in the highest directory level of the card (master