DUSS DIA 303 S Инструкция по эксплуатации - Страница 3
Просмотреть онлайн или скачать pdf Инструкция по эксплуатации для Сверло DUSS DIA 303 S. DUSS DIA 303 S 4 страницы. Diamond core drill
Печатать страницу
Service indicator
The service indicator (5) is located on the lower part of the switch
handle. If the service indicator lights up red, the running time for a
service has been reached. It is possible to work with the machine for
a few more hours from the time the service indicator starts to light up
but will then switches off automatically. Take the power tool to a DUSS
Service Centre as soon as possible to ensure that its serviceability is
maintained.
Mechanical and electric overload protection
The machine is equipped with a mechanical and an electronic overload
protection.
Mechanical overload protection:
The safety clutch protects the user from injury if the rotating tool
suddenly jams.
Electronical overload protection:
The electronics protect the motor from being overloaded. If the contact
pressure is too high, the speed of the drill bit is reduced. This condition
is cancelled by relieving the drill bit and thus the motor. Motor and drill
bit run at nominal speed again.
If the overload lasts longer than 5 seconds, the motor is switched off
electronically. To continue work, the machine must be switched off
and on again after a waiting period of 2 seconds using the pushbutton
switch. The contact pressure must be adjusted.
Before switching the machine on again, make sure that the drill bit can
be turned easily and does not jam in the drill hole.
Lubrication
The entire machine is permanently lubricated by means of a closed
lubrication system.
Maintenance and care
Caution: Always remove the mains plug from the socket before
starting any maintenance and care work.
Clean the machine after finishing work. Also clean the chuck and apply
some dry lubricant spray. Clean the machine with a dry or damp cloth
and not with a jet of water. Ensure that no water gets into the machine.
Make sure that the ventilation slots are always clean.
Sharpening
Blunt diamond core bits should be sharpened by briefly drilling without
suction at reduced speed and without soft impact in the SP sharpening
plate. Worn or damaged diamond drill bits can be refitted by DUSS
depending on their condition. If a segment breaks off, stop working
immediately, as this will destroy the diamond core bit.
Warranty
The warranty period is 12 months from the date of delivery as shown
on the warranty certificate or invoice. The warranty is valid as long as
the machine has been operated and handled correctly, cleaned and
serviced properly in accordance with the operating instructions and
has not been tampered with by unauthorized persons. The warranty is
limited to the free repair or replacement of parts which become defec-
tive due to production or material faults only. Parts becoming defective
as a result of normal wear or due to tampering by the customer or
others are not covered by this warranty. The warranty is valid only if
genuine DUSS tools, consumables, accessories and spare parts are
used, i.e. only if the technical unit is maintained.
Additional claims are excluded, i.e., DUSS is not liable for direct or
indirect defects or consequential damages, losses or expenses in
connection with the use of, or the inability to use the machine for any
purpose. Implied warranties of usability or suitability for a particular
purpose are excluded.
If a defect is discovered, the machine must be sent immediately to
www.duss.de
Translation of the DIA 303 S original operating instructions
DUSS or a DUSS customer service centre. All previous written or ver-
bal warranties are superseded by the above warranty obligations.
Service
Repairs may only be carried out by a qualified electrician. Failing this,
the operator may be exposed to the risk of accidents. If a fault occurs,
you are accordingly strongly recommended to return the machine to
the following address
Alternatively send it to a DUSS customer service centre.
Their experienced specialists and special equipment allow them to
rectify faults properly.
The machine is to be returned complete, at the sender's risk and
expense.
Safety precautions
Read all the safety notes and instructions!
Failure to observe these may cause an electric shock, fire and/or seri-
ous injuries.
Keep the safety notes and instructions for future reference.
Safety precautions
Wear appropriate protective equipment, e.g.
Observe the accompanying safety instructions and the applicable regu-
lations issued by your trade association or similar.
Additional safety precautions
Wear ear protection when impact drilling.
Exposure to noise can cause hearing loss.
Use auxiliary handle supplied with the power tool.
Before starting make sure that the swivelling side handle and the auxi-
liary handle are firmly screwed in at the desired position. Always hold
the machine with both hands when working and maintain a firm stance.
Work concentrated. Loss of control of the power tool can cause perso-
nal injury.
Hold power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden
3