Dust Care 4000 Quiet Series Руководство по установке - Страница 9

Просмотреть онлайн или скачать pdf Руководство по установке для Пылесос Dust Care 4000 Quiet Series. Dust Care 4000 Quiet Series 11 страниц. Central vacuum systems

Печатать страницу

NOTE:

The use of the 90° Ell (stock no. 2004-HXH) is or 4" walls, while the special short

90° Ell (stock no. 2021-HXS) should be used for 3" walls.

MOUNTING PLATE

Floor installation - Vinyl or Lino

Cut hole (2 3/8" by 4 3/8") into floor at desired location

and screw mounting plate from below to underside of

floor. Connect tube to mounting plate with a short 90°

Ell (stock no. 2004-HXH).

Connect low-voltage wire to lugs on Inlet valve and screw

inlet valve into place (illustration 1).

Floor installation - Carpeting

Connect coupling (stock no. 2010-HXH ) to mounting

plate. Insert a 1" sleeve of tube (shown as dotted line)

between coupling and short 90° Ell. Connect to tube.

repeat step "B" of fig. 1 (illustration 2).

New construction - Wall rough-in

Cut 2 1/2" hole dead center through bottom plate and

floor with the edge of the hole 1/4" from stud. Push tube

through opening from below. Nail # 1041 mounting plate

at desired height with plaster guard facing room. Push

tube through opening from below. Connect tube with a

short 90° Ell to mounting plate, using the increments for

proper 90° alignment.

Bend low-voltage wire behind mounting plate, leaving

enough length to permit future connection to lugs on

the Inlet valve. Strap low-voltage wire to tubing with

cable ties.

A temporary cardboard dust cover is available to prevent

construction debris entering the installed system. The dust

cover may be imprinted with the name or corporate logo

of the installing company (illustration 3).

New construction - Utility by-pass

Install mounting plates at desired location, slip a short 90°

Ell over the spigot projecting from the back of the mount-

ing plate. Use the 45° increments on back of mounting

plate and line up with the 45° increment on the short 90°

Ell for true 45° alignment. Insert a 2 1/4" pipe sleeve and

slip into a 45° Ell (stock no. 2008-HXH ) again using the

45° increments for proper 45° alignment. Insert pipe into upper hub of 45° Ell. Repeat

step "B" of fig. 1 (illustration 4).

Existing construction - Finished wall

Cut mounting plate along dotted line with hacksaw or

score with razor knife and break flange off. Using the

raised edge of mounting plate as template, scribe exact

opening on wall and cut opening (illustration 5).

Location of Inlet valve

To drill pilot hole, first establish the location of your inlet

valve. To find an unobstructed section in wall (between

studs), tap with your finger on wallboard until it sounds

hollow. Using a 1/8" drill bit, drill a pilot hole right through

floor directly below the selected location and as close to

the baseboards as possible. Insert a coat hanger wire or

Illustration 1

equivalent into hole so that it projects below floor boards.

From underneath floor measure from coat hanger to cen-

ter of 2" x 4" plate, allowing for thickness of baseboard

and wall covering. Drill 2 1/2" hole directly in the center

of 2" x 4" (illustration 6).

Connecting to Mounting Plate

Slip short 90° Ell over projecting spigot at back of mounting plate. Grasp mounting

Illustration 2

plate between forefinger, middle finger and thumb. Tilt mounting plate top first

upward into wall opening until completely inside wall. Pull towards you until mount-

ing plate fits snug into opening, and secure firmly in place with the use of the metal

wall clip, as shown in inset of illustration 8.

Connect low-voltage wire to lugs on back of Inlet valve. Hold entire assembly in place

with a coat hanger wire while twisting the Inlet valve onto the mounting plate. Do not

glue, as rubber seal ring provides maximum air-tightness. Line up mounting-screw

holes and screw Inlet valve to mounting plate.

Note:

The use of the 90° Ell (stock no. 2004-HXH) is for 4" walls, while the special

short 90° Ell (stock no. 2021-HXS) should be used for 3" walls.

Illustration 3

Illustration 4

Illustration 7

Illustration 8

Illustration 5

Illustration 6

Illustration 9