Datalogic Gryphon DX30 Краткое справочное руководство - Страница 2

Просмотреть онлайн или скачать pdf Краткое справочное руководство для Считыватель штрих-кодов Datalogic Gryphon DX30. Datalogic Gryphon DX30 2 страницы.

Печатать страницу

DEFAULT VALUES

USB-KBD DEFAULT SETTINGS

USA keyboard, FIFO enabled, inter-character and inter-code delays disabled,

USB keyboard speed normal.

: code identifier disabled, no field adjustment, code length not

DATA FORMAT

transmitted, no header, terminator = ENTER, character replacement disabled.

RS232 Standard DEFAULT SETTINGS

9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, delay disabled, rx

timeout 5 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled.

: code identifier disabled, no field adjustment, code length not

DATA FORMAT

transmitted, no header, terminator = CR-LF, character replacement disabled.

WEDGE DEFAULT SETTINGS

USA keyboard, caps lock off, caps lock auto-recognition enabled, num lock

unchanged, inter-character and inter-code delays disabled.

: code identifier disabled, no field adjustment, code length not

DATA FORMAT

transmitted, no header, terminator = ENTER, character replacement disable.

PEN DEFAULT SETTINGS

interpret mode, conversion to code 39 disabled, output level normal, idle level

normal, minimum output pulse 600 μs, overflow medium, inter-block delay disabled.

CODE SELECTION

Enabled codes

•

EAN 8/EAN 13 / UPC A/UPC E without ADD ON

check digit transmitted, no conversions

•

Interleaved 2/5

check digit control and transmission, variable length code; 4-99 characters

•

Standard Code 39

no check digit control, variable length code; 1-99 characters

•

Code 128

variable length code; 1-99 characters

Disabled codes

EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes, MSI,

Plessey, Telepen, Delta IBM, Code 11, Code 16K, Code 49, RSS Codes

TECHNICAL FEATURES

Gryphon™ Dx30

Electrical Features

5 Vdc ± 5%

Power Supply

Consumption:

Gryphon D130

Gryphon D230

Maximum

270 mA@ 5 Vdc

Operating

165 mA@ 5 Vdc

210 mA@ 5 Vdc

Sleep mode/USB Suspend

<500 µA@ 5 Vdc

4 mA@ 5 Vdc

Max. Scan Rate

270 scans/sec

Reading Indicators

LED, Good Read Spot, Beeper

Optical Features

Sensor

CCD solid state (3648 pixels)

Illuminator

LED array

Wavelength

630 ~ 670 nm

Max. LED Output Power

0.33 mW

LED Safety Class

Class 1 EN 60825-1

Gryphon D130-Std

2 ~ 37 cm (20 mils)

Gryphon D130-LR

1 ~ 55 cm (20 mils)

Reading

Field

2 ~ 25 cm (20 mils)

Gryphon D230

3 ~ 14 cm (15 mils) for PDF417 code

Max. Resolution

Gryphon Dx30-Std

Gryphon D130-LR

0.076 mm (3 mils)

0.11 mm (4.3 mils)

PCS (Datalogic Test Chart)

min. 15%

Environmental Features

0 °C to + 55 °C / 32° to +131 °F

Working Temperature

Storage Temperature

-20 °C to + 70 °C / -4° to +158 °F

Humidity

90% non condensing

IEC 68-2-32 Test ED

Drop Resistance

1.8 m (5 ft 11 in)

Protection Class

IP30

Mechanical Features

Weight (without cable)

about 210 g (7.4 oz)

Cable Length

2 m (6 ft 6 in)

RESTORE DEFAULT

Ì$+$*oÎ

To change the defaults refer to the "Gryphon™ Dx30/Mx30 Reference Manual",

part number 90ACC1930, or to the Datalogic Aladdin™ Configuration program,

both downloadable from the website.

INTERFACE SELECTION

Select one of the interface codes according to your application.

USB INTERFACE SELECTION

USB-KBD

Ì$+UA03$-:Î

USB-KBD - ALT-mode

Ì$+UA04$-@Î

USB-COM *

Ì$+UA02$-4Î

USB-IBM-Hand Held

Ì$+UA01$-.Î

* When configuring USB-COM, the relevant files and drivers must be installed

from the USB Device Installation software, which can be downloaded from the

web site http://www.scanning.datalogic.com.

PEN EMULATION INTERFACE SELECTION

PEN

Ì$+CP6$-BÎ

RS232 INTERFACE SELECTION

RS232 Standard

Ì$+CP0$-$Î

Nixdorf Mode A

Ì$+CM2EC0$->Î

Fujitsu

Ì$+CM1$-ÈÎ

ICL Mode

Ì$+CM0$-ÃÎ

WEDGE INTERFACE SELECTION

Wedge IBM AT or PS/2 PCs

Ì$+CP500$-aÎ

PC Notebook

Ì$+CP505$-ÈÎ

PC Notebook - ALT mode

Ì$+CP508$-2Î

IBM AT - ALT mode

Ì$+CP507$-+Î

Many other interfaces are supported and can be selected from the "Gryphon™

Dx30/Mx30 Reference Manual" available online at www.scanning.datalogic.com.

Other supported interfaces:

USB: USB-IBM-Table Top; USB-KBD-APPLE

WEDGE: IBM XT; IBM SURE1; IBM Terminal 3153; IBM Terminals 31xx, 32xx,

34xx, 37xx; Wyse Terminals ANSI – PC –ASCII – VT220 style Keyboards; Digital

Terminal VT2xx/VT3xx/VT4xx; APPLE ADB Bus

KEYBOARD NATIONALITY

USB-KBD and Wedge users should select one of the following wedge keyboard

nationality codes according to your keyboard.

Belge

Ì$+FJ7$-8Î

Deutsch

Ì$+FJ3$-$Î

English

Ì$+FJ4$-)Î

Español

Ì$+FJ6$-3Î

Français

Ì$+FJ2$-ÊÎ

Italiano

Ì$+FJ1$-ÅÎ

Japanese

Ì$+FJ8$-=Î

Svenskt

Ì$+FJ5$-.Î

USA (Default)

Ì$+FJ0$-|Î

DATA FORMAT TERMINATORS

For your convenience, some common Terminators are given below. For other

Header/Terminator selections, Data Format and Advanced Data Format

parameters, see the "Gryphon™ Dx30/Mx30 Reference Manual".

CR-LF

Ì$+EA120D0A$-ÃÎ

Enter

Ì$+EA1183$-0Î

Tab

Ì$+EA1184$-8Î

None

Ì$+EA10$-dÎ

USING GRYPHON™ DX30 READERS

Gryphon™ guns automatically scan barcodes at a distance. Simply aim and pull

the trigger. Code scanning is performed along the center of the light bar emitted

from the reading window. This bar must cover the entire code.

Successful scanning is obtained by tilting the scanner with respect to the barcode

to avoid direct reflections, which impair the reading performance, see the figure

above.

Successful reading is signaled by an audible tone plus a good-read green spot.

OPERATING TEST

Read the TEST codes below.

EAN-8

1 2 3 4 5 6 7 0

EAN-13

1 2 3 4 5 6 7 0 0 0 9 9 2

Code 39 (Normal)

Code 128

Interleaved 2 of 5

0 1 2 3 4 5 6 7 8 4