Datalogic Jet Краткое руководство по эксплуатации
Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Док-станция Datalogic Jet. Datalogic Jet 2 страницы. Vehicle cradle
Также для Datalogic Jet: Руководство пользователя (2 страниц), Руководство пользователя (2 страниц)
Печатать страницу
Datalogic Jet™ Ethernet Multi Cradle
The Datalogic Jet™ Ethernet Multi Cradle provides power for charging up
to four mobile computers simultaneously and also connects up to four
mobile computers to an Ethernet network.
A
F
E
D
Figure 1 – Datalogic Jet™ Ethernet Multi Cradle General View
Key:
A)
Link LED for Ethernet Port 1
B)
Speed LED for Ethernet Port 1
C)
Datalogic Jet™ Charging Status LED
D)
Power supply connector
E)
Ethernet Port 1 (with integrated Link and Speed LEDs)
F)
Ethernet Port 2 (with integrated Link and Speed LEDs)
822000751 (Rev. A)
The Ethernet cradle drivers are pre-installed on the Datalogic Jet™ and
initiate automatically when the Datalogic Jet™ is placed in a properly
connected Four Slot Ethernet cradle.
When the mobile computer is inserted into the Four Slot Ethernet cradle,
the LAN icon indicates that the mobile computer is connected to a
network.
Ethernet communication requires Datalogic Jet™ PDA
SW version 5.41 or later. Verify the software version
by tapping on Software – Version in the Datalogic
default home page. Otherwise, search for the file
version.htm under the Windows folder.
NOTE
The green Speed LED lights to indicate that the transfer rate is 100 Mbps.
When it is not lit it indicates that the transfer rate is 10Mbps.
C
The maximum bandwidth capacity for each Mobile
Computer is 12Mbps.
NOTE
B
The yellow Link LED blinks to indicate activity, or stays lit to indicate that
a link is established. When it is not lit it indicates that there is no link.
The Speed LED and the Link LED integrated in Ethernet Port 1 and 2
function in the same way.
The Charging Status LED on the mobile computer shows the status of the
battery charging. The maximum time required to recharge a completely
run-down battery pack is about 2.5 hours for Li-Ion batteries. See
Datalogic Jet™ User's Manual par. 3.5.1 for Charging Status LED
indications.
Correct Mobile Computer Insertion / Removal
Insert the mobile computer into a slot to begin charging and start
communication.
For correct insertion onto the cradle, insert the mobile computer from the
top of the cradle and push it down firmly.
Figure 2 - Mobile Computer Insertion
To remove the mobile computer from the Datalogic Jet™ Ethernet Multi
Cradle, simply pull it upwards while holding the cradle firmly down.
TECHNICAL FEATURES
Electrical Features
Power supply *
from 12 to 14 VDC ± 5%
Consumption
Max 4.2 A
Indicators
Ethernet Link LED (yellow)
Ethernet Speed LED (green)
Charge time (when PDA is off)
max 2.5 hours (Li ION batteries)
Communication Features
Interface
Ethernet 10/100 Base T
Environmental Features
Working temperature
0° to +50°C / 32° to 140°F **
Storage temperature
-20° to +70°C / -4° to 158°F
Humidity
90% non condensing
Degree of protection
IP20
Mechanical Features
Dimensions
480 x 110 x 190 mm
18.89 x 4.33 x 7.48 in
Weight
about 2750 g / 97 oz
*
Recommended DL power supply: FPS18.
**
Batteries must be charged at a temperature ranging from 0° to 45 °C
(+32° to 113°F).